Rigol MSO5000 Series Скачать руководство пользователя страница 200

Страница: 200 / 358

RIGOL

Chapter 9 Histogram Analysis

9-4

MSO5000 User's Guide



Sum: indicates the sum of all bins (buckets) in the histogram.



Peaks: indicates the maximum number of hits in any single bin.



Max: indicates the maximum value within the histogram range.



Min: indicates the minimum value within the histogram range.



Pk_Pk: indicates the Delta between the max. value and the min. value.



Mean: indicates the average value of the histogram.



Median: indicates the median value of the histogram.



Mode: indicates the mode value of the histogram.



Bin width: indicates the width of each bin (bucket) in the histogram.



Sigma: indicates the standard deviation of the histogram.

To Reset

Press

Reset

to reset the statistical data and restart to make statistics.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MSO5000 Series







































































































































































































































































































































































Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol MSO5000 Series, Руководство пользователя

Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды