13
IMPIANTO ELETTRICO
LEGENDA (Fig. 14 - 15 - 16)
CMP
- Contattore motore pompa
CMV
- Contattore motore ventilatore
CR
- Contattore resistenze
RBO 522R - Apparecchiatura elettrica
FR
- Fotoresistenza
IN
- Interruttore elettrico per arresto manuale bruciatore
I1
- Interruttore: “bruciatore acceso-spento”
I2
- Interruttore: “1° - 2° stadio”
MB
- Morsettiera bruciatore
MR
- Morsettiera resistenze
MV
- Motore ventilatore
MP
- Motore pompa
MPR
- Morsettiera preriscaldatore
PO
- Pressostato di consenso pressione anello
PR
- Serbatoio preriscaldatore
R
1,2,3
- Resistenza preriscaldatore
RS
1,2,3,4
- Resistenza di mantenimento
RT
- Relè termico motore ventilatore
RT1
- Relè termico motore pompa
S
- Segnalazione di blocco a distanza
SM
- Servomotore
SO
- Sonda Pt 100
T
- Trasformatore termoregolatore
TA
- Trasformatore d’accensione
TB
- Terra bruciatore
TE
- Termoregolatore
TL
- Telecomando di limite: ferma il bruciatore quando la
temperatura o la pressione in caldaia supera il valore
prestabilito
Tm
- Termostato a contatto di minima
TM
- Termostato a contatto di massima
TMR
- Termostato a contatto di massima a riarmo manuale
TP
- Terra preriscaldatore
TR
- Telecomando di regolazione: comanda 1° e 2° stadio
di funzionamento. Necessario solo nel funzionamento
bistadio.
TS
- Telecomando di sicurezza: interviene in caso di TL
guasto.
X
- Spina di collegamento bruciatore/bag
XP
- Presa di collegamento bruciatore/bag
U
- Led Panel
VP
- Elettrovalvola di prelavaggio
V1
- Elettrovalvola di 1° stadio
V2
- Elettrovalvola di 2° stadio
NOTA
Per avere lo sblocco a distanza collegare un pulsante (NA) fra il
morsetto 4 e il neutro dell’apparecchiatura (morsetti 15, 16, 17 e 18).
ELECTRICAL SYSTEM
KEY TO LAYOUTS (Fig. 14 - 15 - 16)
CMP
- Pump motor contactor
CMV
- Fan motor contactor
CR
- Resistance contactor
RBO 522R - Control box
FR
- Photoresistance
IN
- Manual burner stop switch
I1
- Switch: “burner on-off”
I2
- Switch: “1st - 2nd stage”
MB
- Burner terminal strip
MR
- Resistance terminal strip
MV
- Fan motor
MP
- Pump motor
MPR
- Pre-heater terminal strip
PO
- Loop pressure enable pressure switch
PR
- Pre-heater
R
1,2,3
- Pre-heater resistance
RS
1,2,3,4
- Maintaining heating element
RT
- Fan motor thermal cut-out
RT1
- Pump motor thermal cut-out
S
- Remote lock-out signal
SM
- Servomotor
SO
- Sonde Pt 100
T
- Temperature controller transformer
TA
- Ignition transformer
TB
- Burner ground (earth) connection
TE
- Temperature controller
TL
- Limit control device: this shuts down the burner when
the boiler temperature or pressure exceeds the set-
point value.
Tm
- Minimum value contact thermostat
TM
- Maximum value contact thermostat
TMR
- Maximum value contact thermostat with manual reset
TP
- Pre-heater ground (earth) connection
TR
- High-low mode control: this controls operating stages
1 and 2 and is necessary only for two-stage operation.
TS
- Safety control: this operates when TL is faulty.
X
- Burner/Bag connection plug
XP
- Burner/Bag connection socket
U
- Led Panel
VP
- Pre-purge solenoid-valve
V1
- 1st stage solenoid valve
V2
- 2nd stage solenoid valve
NOTE
For remote reset, connect a push-button switch (NO) between termi-
nal 4 and neutral wire of the control box (terminals 15, 16, 17 and
18).