Ricoh SH-P1 M020 Скачать руководство пользователя страница 212

Страница: 212 / 312

7807 001

Reset-SC/Jam

Resets the SC and jam counters. To reset, press
[#Enter].

• This SP does not reset the jam history counter:

SP7-507

7832

Display-Self-Diag

7832 001

Display-Self-Diag

Press [OK] to display a list of error codes. Nothing is
displayed if no errors have occurred.

7836

Resident Memory

7836 001

Resident Memory

Displays the memory capacity of the controller system.

7901

Assert Info.

7901 001

File Name

Records the location where a problem is detected in
the program. The data stored in this SP is used for
problem analysis.

7901 002

Number of Lines

7901 003

Location

7904

Near End Timing

7904-001

Maintenance Kit

Sets the Near End Timing of the Maintenance Kit.
[0 to 2 / 1 / 1]

7931

AIO Information

Displays information about the AIO.

• Returns a value of "0" if the number stored in the cartridge is not recognized.
• This is information on the AIO ID Chip so if the AIO is not installed, if the AIO is

not set properly, or if the front door is open, no value will be displayed because
the machine cannot communicate with the AIO.

7931 001

Machine ID

Identification number of the machine (Model Name)
[0x00 to 0xFF / 0x00 / 0x01]

5. System Maintenance Reference

210

Содержание SH-P1 M020

























































































































































































































































































































Результаты поиска

Содержание SH-P1 M020

Отзывы:

Похожие инструкции для SH-P1 M020

Бренды по названию

Популярные бренды

Ricoh SH-P1 M020, Руководство по обслуживанию на месте

Результаты поиска

Содержание SH-P1 M020

Отзывы:

Похожие инструкции для SH-P1 M020

Бренды по названию

Популярные бренды