Ricoh SH-P1 M020 Скачать руководство пользователя страница 162

Страница: 162 / 312

5801 017

CCS

Initializes the CCS (Certification and Charge-control
Service) settings.

5801 018

SRM Memory Clr

Initializes information in non-volatile RAM.

5801 019

LCS

Initializes information in non-volatile RAM.

5801 021

ECS

Initializes the ECS settings.

5802

Free Run

Execution of a Free Run

5802 001

Free Run

The machine performs a free run.
[0 to 1 / 0 / 1]
Press [#Enter] to start.
Press [#Enter] to stop.

• The machine will not stop immediately after the

[#Enter] key is pressed.

5803

Input Check

Displays signals received from sensors and switches.
SP Modes other than those listed in this table, are not used in the machine.

Operation Panel

Component Name

5803 001

Cover Open

Cover sensors
[0x00 to 0x11 / 0x00 / 0x01]

5803 002

Main Motor: Lock

Main Motor lock
[0x00 to 0x01 / 0x00 / 0x01]

5803 003

Polygon: Lock

Polygon Motor lock
[0x00 to 0x01 / 0x00 / 0x01]

5803 005

Main FAN: Lock

Exhaust fan
[0x00 to 0x01 / 0x00 / 0x01]

5803 006

PSU FAN: Lock

PSU fan
[0x00 to 0x01 / 0x00 / 0x01]

5. System Maintenance Reference

160

Содержание SH-P1 M020

























































































































































































































































































































Результаты поиска

Содержание SH-P1 M020

Отзывы:

Похожие инструкции для SH-P1 M020

Бренды по названию

Популярные бренды

Ricoh SH-P1 M020, Руководство по обслуживанию на месте

Результаты поиска

Содержание SH-P1 M020

Отзывы:

Похожие инструкции для SH-P1 M020

Бренды по названию

Популярные бренды