Ricoh SH-P1 M020 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 312

background image

• To release the left side flat cable, pull out the black tab [C] of the connector half way.
• Do not touch the LCD unit surface [D].

NVRAM and EEPROM

NVRAMs

1. Print the SMC data (”ALL”) using SP5-990-001 (  p.138).
2. Turn off the main switch.
3. Remove the VM card from SD card Slot 2 (Lower).
4. Insert a blank SD card into Slot 2 (Lower), and then turn on the main power switch.
5. Upload the NVRAM data to the blank SD card using SP5-824-001 (  p.138, p.231).
6. Turn off the main power switch, and then unplug the AC power cord.
7. Remove the SD Card containing the NVRAM data from Slot 2 (Lower).
8. Replace the NVRAMs on the Controller Board with a new ones (  p.96).
9. Plug in the AC power cord, and then turn on the main power switch

• When you do this, SC995-02 (Defective NVRAM) will be displayed. However, do not turn

off the main power switch. Continue this procedure.

10. Re-insert the SD card that you removed in Step 7 back into Slot 2 (Lower)
11. Download the old NVRAM data from the SD card onto the new NVRAMs using SP5-825-001 (

• This will take about 2 or 3 minutes.

12. Turn off the main power switch, and then remove the SD card from Slot 2 (Lower).

Electrical Components

109

4

«
...
109
110
111
112
113
...
»

Содержание SH-P1 M020

























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH-P1 M020

Бренд: SA Страницы: 5

Бренд: Radio Shack Страницы: 62

Бренд: Samsung Страницы: 134

Бренд: Zebronics Страницы: 6

7400DT - Phaser Color LED Printer

Бренд: Xerox Страницы: 20

WorkCentre PE120i

Бренд: Xerox Страницы: 8

Бренд: Oki Страницы: 4

Бренд: idp Страницы: 63

Бренд: Oakton Страницы: 8

Бренд: IBM Страницы: 16

Бренд: Kyocera Страницы: 12

Бренд: Konica Minolta Страницы: 46

Бренд: TRENDnet Страницы: 135

Бренд: Lexmark Страницы: 2

Бренд: Oki Страницы: 78

Бренд: WOOSIM Страницы: 17

Бренд: Canon Страницы: 2

Advanced MXM365N

Бренд: Sharp Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды