manualshive.com logo in svg

Ricoh LDD250, Руководство по обслуживанию

Поделиться
Скачать
Ricoh LDD250 Скачать руководство пользователя страница 355

 

MASTER EJECT 

SM 6-33 

C262/C265 

Detailed 

Des

cription

s 

6.5.5  PRESSURE PLATE DRIVE MECHANISM 

Overview 

There are three phases. 

•

 Homing 

At power on or when recovering from an error or jam, the machine makes sure 
that the pressure plate is at home position. This is because, if certain errors 
occur, the pressure plate may not be in the home position at the start of a job 

•

 Master ejection 

The pressure plate rotates into a position where it can act as a feed guide for the 
used master on its way to the eject box. 

•

 Compression 

The pressure plate compresses the master into the box. 

 

Drive 

 
 

 
The pressure plate motor [A] drives the pressure plate [B] through the pressure 
plate gear [C]. This gear contains actuators for the home position sensor [D] and 
the limit position sensor [E]. These two sensors monitor the pressure plate position. 
The diagram shows a front view of the mechanism. The actuators are on the rear 
of the pressure plate gear, which is shown as see-through for ease of viewing. 
 
 

 

C262D022.WMF 

[A]

[B]

[C] 

[D]

[E]

Содержание LDD250












































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды