Ricoh LDD250, Руководство по обслуживанию

Страница: 15 / 459

SM iii C262/C265
3.7.3 THERMAL HEAD............................................................................3-32
3.7.4 DUCT ENTRANCE SOLENOID .....................................................3-33
3.7.5 CUTTER UNIT, MASTER FEED CONTROL MOTOR, CLAMP
TENSION ROLLER, UPPER MASTER FEED CONTROL ROLLER........3-34
3.7.6 PLATEN RELEASE SENSOR, PLATEN RELEASE MOTOR ........3-37
3.7.7 MASTER AMOUNT SENSOR ........................................................3-39
3.7.8 MASTER DUCT SENSOR, MASTER SUCTION FANS,
MASTER FEED MOTOR................................................................3-40
3.7.9 MASTER SET SENSOR, MASTER EDGE SENSOR.....................3-42
3.7.10 FLAT CABLE ................................................................................3-43
3.7.11 MASTER END SENSOR ..............................................................3-43
3.7.12 MASTER BUFFER FANS.............................................................3-44
3.7.13 UNIT LOCK SOLENOID, 2ND DRUM MASTER SENSOR ..........3-44
3.7.14 PLATEN RELEASE CAM ADJUSTMENT ....................................3-46
3.7.15 THERMAL HEAD VOLTAGE ADJUSTMENT...............................3-47
3.7.16 MASTER END SENSOR ADJUSTMENT .....................................3-48
3.7.17 MASTER EDGE SENSOR ADJUSTMENT ..................................3-49
3.7.18 MASTER SET SENSOR ADJUSTMENT......................................3-50
3.7.19 THERMAL HEAD ALIGNMENT ADJUSTMENT...........................3-52
3.7.20 MASTER MAKING UNIT PARALLEL ADJUSTMENT ..................3-53
3.7.21 MASTER EDGE TRIMMING PROCEDURE.................................3-55
3.7.22 MASTER FEED MYLAR POSITIONING ......................................3-57
3.8 DRUM SECTION.....................................................................................3-58
3.8.1 DRUM UNIT ...................................................................................3-58
3.8.2 DRUM CLOTH SCREEN................................................................3-58
3.8.3 DRUM MASTER CLAMPER, METAL SCREEN .............................3-61
3.8.4 MOTORS AND SENSORS IN THE DRUM ....................................3-64
3.8.5 INK ID DETECTION/INK FLOW SENSOR CONNECTOR .............3-67
3.8.6 INK ROLLER GAP ADJUSTMENT.................................................3-68
3.8.7 INK DETECTION ADJUSTMENT ...................................................3-70
3.8.8 DRUM POSITION ADJUSTMENT..................................................3-72
3.8.9 1ST DRUM MASTER SENSOR ADJUSTMENT ............................3-74
3.8.10 2ND DRUM MASTER SENSOR ADJUSTMENT..........................3-76
3.9 PAPER FEED SECTION.........................................................................3-78
3.9.1 PAPER TABLE UNIT, PAPER FEED ASSEMBLY.........................3-78
3.9.2 PICK-UP ROLLER, PAPER FEED ROLLER..................................3-80
3.9.3 PAPER WIDTH DETECTION BOARD ...........................................3-81
3.9.4 PAPER HEIGHT SENSOR.............................................................3-82
3.9.5 FEED PRESSURE MOTOR, FEED PRESSURE
DETECTION BOARD .....................................................................3-83
3.9.6 REGISTRATION PRESSURE MOTOR, REGISTRATION ROLLER
PRESS SENSOR, REGISTRATION ROLLER RELEASE SENSOR ......3-84
3.9.7 PAPER REGISTRATION SENSOR, PAPER FEED
TIMING SENSOR ...........................................................................3-85
3.9.8 UPPER REGISTRATION ROLLER ................................................3-89
3.9.9 FRICTION PADS............................................................................3-90
3.9.10 SEPARATION PRESSURE DETECTION BOARD,
FRICTION PAD SHIFT MOTOR...................................................3-91
3.9.11 SEPARATION PRESSURE MOTOR, FRICTION PAD