Ricoh LDD250 Скачать руководство пользователя страница 169

Страница: 169 / 459

PAPER FEED SECTION

C262/C265 3-94

[H]: Bearing holder (

x 2)

[I]: Bearing
[J]: Lower registration roller

NOTE:

Slide the lower registration roller [J] towards the operation side.

3.9.13 REGISTRATION ROLLER LIFTING CAM POSITION

ADJUSTMENT

Purpose: To ensure smooth paper feed from the registration roller to the drum.

NOTE:

Make sure that the drum is at home position before the adjustment.

1. When installing the registration roller lifting cam [A] on the shaft, align the cam

follower (a bushing) at the center or within one division to the right of the center.

2. If the cam follower cannot be put in the correct place, try to change the gear

meshing. Also, try to readjust the position by loosing the screw holding the cam
to the gear.

NOTE:

To obtain a perfect adjustment, you must take out any gear play by
applying clockwise pressure to the cam (with the gear) during the
adjustment.

C262R092.WMF

[A]

Содержание LDD250












































































































































































































































































































































































































































































Результаты поиска

Содержание LDD250

Отзывы:

Бренды по названию

Популярные бренды

Ricoh LDD250, Руководство по обслуживанию

Результаты поиска

Содержание LDD250

Отзывы:

Бренды по названию

Популярные бренды