Ricoh LDD250 Скачать руководство пользователя страница 252

Страница: 252 / 459

ELECTRICAL COMPONENT DEFECTS

C262/C265 4-18

Name State

Symptoms

Detects that the table is
closed, but it is open.

The machine displays “Open the paper
table” after the main switch is turned on.

Paper table set sensor

Detects that the table is
open, but it is closed.

The paper table does not move up after
the Print button is pushed.

Detects paper, but there
is no paper

A jam occurs when the Print button is
pushed.

Paper end sensor

Does not detect paper,
but there is paper

The machine displays “Add paper” after
the main switch is turned on.

Detects pressure, but
there is not.

The feed pressure detection board detects
the pressure continually when the print
button is pushed
SC500: Feed pressure motor lock

Feed pressure
detection board

Does not detects
pressure, but there is
pressure.

The feed pressure detection board does
not detect the pressure continually when
the print button is pushed
SC500: Feed pressure motor lock

Detects pressure, but
there is not.

The separation pressure detection board
detects the pressure continually when the
print button is pushed.
SC501: Separation pressure motor

Separation pressure
detection board

Does not detects
pressure, but there is
pressure.

The separation pressure detection board
does not detect the pressure continually
when the print button is pushed
SC501: Separation pressure motor

Stays on (detects a
friction pad, but one is not
there)

If the sensor does not turn off for 5
seconds when the friction pad is changing
to thick paper, SC505 occurs (friction pad
shift motor).

Friction pad position
sensor 1

Stays off (does not detect
a friction pad, but one is
there)

If the sensor does not turn on for 5
seconds when the friction pad is changing
to normal paper, SC505 occurs (friction
pad shift motor).

Stays on (detects a
friction pad, but one is not
there)

A paper jam or double feed occurs,
because the friction pad does not stop at
the correct position.

Friction pad position
sensor 2

Stays off (does not detect
a friction pad, but one is
there)

If the sensor does not turn on for 5
seconds when the friction pad is changing,
SC505 occurs (friction pad shift motor).

4.4.7 PRINTING AND PRESSURE CYLINDER

Name State

Symptoms

Stays on (detects that
clamper is open, but it is
not)

If the sensor does not turn off when the
clamper motor is opening and closing the
clamper, SC314 (clamper motor lock)
occurs.

Clamper open position
sensor

Stays off (detects that
clamper is closed, but it is
not)

If the sensor does not turn on when the
clamper motor is opening and closing the
clamper, SC314 (clamper motor lock)
occurs.

Содержание LDD250












































































































































































































































































































































































































































































Результаты поиска

Содержание LDD250

Отзывы:

Бренды по названию

Популярные бренды

Ricoh LDD250, Руководство по обслуживанию

Результаты поиска

Содержание LDD250

Отзывы:

Бренды по названию

Популярные бренды