manualshive.com logo in svg

Ricoh LDD250, Руководство по обслуживанию

Поделиться
Скачать
Ricoh LDD250 Скачать руководство пользователя страница 249

 

ELECTRICAL COMPONENT DEFECTS 

SM 4-15 

C262/C265 

Trouble-

shooting 

Name State 

Symptoms 

The sensor detects the 
drum is at the 2

nd

 

position, but it is not 

The drum will not stop after one sheet of 
paper is fed when the Start button is 
pushed. 

The sensor detects the 
drum is not at the home 
position, but it is 

The green LED stays lit and the red LED 
stays off. 

Drum home position 
sensor 

The sensor detects the 
drum is at the home 
position, but it is not 

The green LED stays off and the red LED 
stays lit. 
SC302 (drum home position sensor error) 
occurs after the drum tries to move to 
home position 3 times when the front 
cover is opened and closed. 

Short circuit 

SC307 occurs immediately after the main 
switch is turned on. 

Thermistor 

Broken wire 

SC306 occurs immediately after the main 
switch is turned on. 

Detects ink, but there is 
no ink 

The printed image is patchy because ink 
is not supplied when the Start button is 
pushed. 

Ink detection pin 
 

Does not detect ink, but 
ink is present 

Excess ink is supplied, but the overflow 
sensor will detect the overflow and 
prevent the ink leakage.  
Replace or clean the ink detection pin  

Detects a cartridge, but 
no cartridge is present 

The printed image will be pale, because 
the drum tries to supply ink without an ink 
cartridge. 

Ink cartridge set 
switch 

Does not detect a 
cartridge, but a cartridge 
is present 

The machine displays “Set ink cartridge” 
after the main switch is turned on.  

Drum shift sensor 
 

Does not detect a signal  If a signal does not come from the 

encoder for 6 seconds, SC305 occurs 
(drum shift motor lock). 

Drum shift HP sensor 
 

Does not detect a signal  SC304 (drum shift motor lock) occurs if 

one of these two conditions occurs: 

•

  The drum does not go back to home 

position within 3 seconds. 

•

  The drum does not go to the 

requested drum shift position within 6 
seconds.  

Stays on 

If the sensor does not turn off, SC308 (ink 
pump motor lock) occurs. 

Ink pump sensor 

Stays off 

If the sensor does not turn on, SC308 (ink 
pump motor lock) occurs. 

Stays on (detects that the 
idling roller is at home 
position, but it is not) 

If the sensor does not turn off more than 4 
seconds after the main switch is turned 
on, SC315 (idling roller motor lock) 
occurs. 

Idling roller HP sensor 

 

If the sensor does not turn on more than 4 
seconds after the main switch is turned 
on, SC315 (idling roller motor lock) 
occurs. 

Содержание LDD250












































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды