RichAuto A122, Руководство пользователя

Страница: 35 / 55

Add: 5F, No.4 building, No 4. Yard, life Rd, life science park,
Tel
：
010-53275118 Fax
：
Home direction : Each axis motion direction when return home. This setting depends
on the installation position of home sensor. If the home sensor is installed at the
positive side of machine tool, then it should
machine tool, should be set as “Neg”.
Setting method
：
Enter “home direction”
users want to modify. Press“
save the change.
5. Acceleration(Unit
：
mm/s
The maximum acceleration value
improve (including straight
is too large, it may cause the motor losing
small, it will lead to accelerated slowly and reduce the operating speed of the entire graph.
System defaults: linear acceleration
recommended curve acceleration is 1.5
6. Voltage setup
Set input and output signal terminal status(normal open or normal closed)
“
↓ ”means normal open
，
“ ↑ ”means normal closed.
Including two rows of arrow
The upper arrow indicates the input level
The first four:0
、
1
、
2
、
3positions correspond X
tool setting signal; 5-7: 4
、
signal.
The bottom arrow indicates the output level
The top four: 0
、
1
、
2
、
3 positions correspond
defined1, port to be defined 2
is work type changing signal
Setting
：
Press“ ”
、
“
move up and down
，
press“
7. Max. work speed(Unit:mm/min)
The maximum movement speed of the three axis of the machine tool
only takes effect during processing,
System default max work
mm/minute”, “Z+” is “1800 mm/minute”, “Z
8. Function setup
Set whether the system reserves a function or not, change it according
application. Restart the system
Beijing RichAuto S&T Co., Ltd
, No.4 building, No 4. Yard, life Rd, life science park, Beiqing St., Changping dist.
：
010-53275110/53275111 Web site
：
www.richnc.com.cn
: Each axis motion direction when return home. This setting depends
on the installation position of home sensor. If the home sensor is installed at the
positive side of machine tool, then it should be set “pos”; if it is at the negative side of
l, should be set as “Neg”.
Enter “home direction”
，
press“ ”
、
“ ” to move cursor to where
users want to modify. Press“ ”to change home direction
，
after that press“
mm/s
2
)
The maximum acceleration value during acceleration and deceleration movement,
and curve motion) processing capability. If acceleration
is too large, it may cause the motor losing steps, jitter and even whistle, if
celerated slowly and reduce the operating speed of the entire graph.
linear acceleration is 800 mm/s2, curve acceleration is 1000
recommended curve acceleration is 1.5 - 2 times of the linear acceleration.
t and output signal terminal status(normal open or normal closed)
，
”means normal closed.
Including two rows of arrow
：
The upper arrow indicates the input level
：
Set input voltage signal terminal status.
3positions correspond X axis home
、
Y axis home
、
Z axis home and
、
5
、
6 positions correspond driver alarm , hard limit and E
The bottom arrow indicates the output level
：
Set output voltage signal terminal
3 positions correspond in turn by spindle forward, port to be
defined1, port to be defined 2 and spindle inversion output signal port ; No.6 position
work type changing signal.
”to move left and right, press “ ”
、
“
press“ ”to change the direction of each arrow.
(Unit:mm/min)
The maximum movement speed of the three axis of the machine tool during
effect during processing, and not limits the speeds under manual mode.
work speed of X,Y(both pos and neg direction)
is “1800 mm/minute”, “Z-”is “3000 mm/minute”.
Set whether the system reserves a function or not, change it according
pplication. Restart the system after the operations.
（
pic. as shown below
Beijing RichAuto S&T Co., Ltd
ist. Beijing, China
www.richnc.com.cn 31
: Each axis motion direction when return home. This setting depends
on the installation position of home sensor. If the home sensor is installed at the
set “pos”; if it is at the negative side of
” to move cursor to where
after that press“ ” to
during acceleration and deceleration movement,
. If acceleration value
steps, jitter and even whistle, if the value too
celerated slowly and reduce the operating speed of the entire graph.
, curve acceleration is 1000 mm/s2, the
2 times of the linear acceleration.
，
system defined
Set input voltage signal terminal status.
Z axis home and
6 positions correspond driver alarm , hard limit and E-stop
Set output voltage signal terminal status.
spindle forward, port to be
port ; No.6 position
“ ”realize to
during processing. It
the speeds under manual mode.
(both pos and neg direction) is“60000000
Set whether the system reserves a function or not, change it according to the actual
as shown below
）