Rheem 834 Series Скачать руководство пользователя страница 31

Страница: 31 / 61

TM081 Rheem 834 Series Hydroelectric CFGWH Service Instructions
REV: AA Issued: 22/02/17

This document is stored and maintained electronically by Rheem Technical Support. All printed copies are deemed uncontrolled.

Fault Finding Chart 1.2

Is flame sensor clean

and free from cracks?

Firmly connect flame sensor

lead to flame sensor.

YES

Is flame sensor

correctly adjusted?

YES

Correctly adjust flame sensor.

Refer to ‘Checking & Adjusting

the Flame Sensor’ in the

‘Component Adjustment

Procedures &

Checks’ section.

1.2

Does main burner

ignite?

Is flame sensor lead

firmly connected to

flame sensor?

Clean flame sensor or replace

pilot assembly. (flame sensor is

not available as a spare part).

Is flame sensor rod

touching a metal

component?

YES

Does pilot light during

ignition period?

YES

Is 1.1 ~ 2.1 VDC

present at SV1 during

ignition period?

(TEST 8)

Replace ignition module.

Is pilot feed pipe, pilot

injector or pilot assy

dirty or blocked?

YES

Replace gas valve assembly.

Clean or replace pilot feed pipe

or pilot assembly (pilot injector is

not available as a spare part).

YES

SV1 is pilot

valve

Is pilot flame
satisfactory?

YES

Pilot flame should extend past

flame rod by approx 5 mm and

flame rod should glow red.

Is pilot injector correct

size for gas type?

Replace pilot injector with one of

the correct size.

YES

Is 1.1 ~ 2.1 VDC

present at SV2 when

pilot is alight?

(TEST 9)

SV2 is main burner

safety valve

Replace ignition module

Fault rectified.

Replace temperature controller

and reinstall original ignition

module.

Does red LED 4 flash

fault indication

persist?

YES

Is 1.1 ~ 2.1 VDC

present at SV3 when

pilot is alight?

(TEST 10)

YES

Replace temperature controller.

Replace gas valve assembly.

YES

1.3

YES

False flame, ignition failure or

loss of flame (continued)

SV3 is main

burner valve

Содержание 834 Series






























































Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды

Rheem 834 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды