Rheem 834 Series Скачать руководство пользователя страница 29

Страница: 29 / 61

TM081 Rheem 834 Series Hydroelectric CFGWH Service Instructions
REV: AA Issued: 22/02/17

This document is stored and maintained electronically by Rheem Technical Support. All printed copies are deemed uncontrolled.

Fault Finding Chart 1

YES

Refer to fault finding chart for
the fault indication displayed.

YES

Do temp controller

LED’s indicate a fault

condition?

Heater not operating

Are all wiring plugs

and wiring connectors

firmly connected?

YES

Is water flow rate

through heater

> 3 L/m?

1.1

Firmly connect wiring

connector(s) and/or plug(s).

Are hot tap(s) opened

enough?

Hot tap(s) must be opened

enough i.e. water flow rate

through the heater must be

> 3 L/m.

Is cold water isolation

valve fully open?

YES

Advise customer that water

supply pressure is not within

specification.

Minimum water supply

pressure is 150 kPa.

Is water supply

pressure adequate?

Fully open cold water isolator

located adjacent to heater.

YES

Is water inlet strainer

blocked?

Clean or replace water inlet

strainer.

YES

Is hydroelectric

generator / water flow
sensor assy blocked?

Unblock hydroelectric

generator / water flow sensor

assembly.

YES

Is cold water inlet /

seasonal adjustment

valve assy blocked?

YES

Is water throttle valve

assy blocked?

Unblock or replace cold water

inlet / seasonal adjustment valve

assembly.

Unblock or replace water throttle

valve assembly.

YES

Is hot water outlet

assy blocked?

Unblock or replace hot water

outlet assembly.

YES

Unblock or replace blocked heat

exchanger.

Is pipework to and

from heat exchanger

blocked?

Unblock or replace blocked

pipework.

YES

Содержание 834 Series






























































Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды

Rheem 834 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды