Rheem 834 Series Скачать руководство пользователя страница 25

Страница: 25 / 61

TM081 Rheem 834 Series Hydroelectric CFGWH Service Instructions
REV: AA Issued: 22/02/17

This document is stored and maintained electronically by Rheem Technical Support. All printed copies are deemed uncontrolled.

Fault Finding Chart

– Red LED 4 Flash Indication

Red LED 4 Flash

False flame, ignition

failure or loss of flame

Are all wiring plugs

and wiring connectors

firmly connected?

YES

Firmly connect wiring

connector(s) and/or plug(s).

Replace gas valve assembly.

YES

(false flame)

Is a voltage present

at SV1 prior to

ignition period?

(TEST 5)

Replace temperature controller.

Is pilot or main burner

flame present prior to

ignition period?

Is a voltage present

at SV2 prior to

ignition period?

(TEST 6)

YES

SV1 is pilot

valve

SV2 is main

burner

safety valve

YES

Does ignition module

generate a spark

during ignition

period?

Is ignition rod lead

firmly connected to

ignition rod?

Is ignition rod & pilot

hood clean and free

from cracks?

Firmly connect ignition

rod lead to ignition rod.

Clean ignition rod and/or pilot

hood or replace pilot assembly

(ignition rod is not available as a

spare part).

YES

Is ignition rod gap

correct?

YES

Correctly adjust ignition rod gap.

Refer to ‘Checking & Adjusting

the Ignition Rod Gap’ in the

‘Component Adjustment

Procedures &

Checks’ section.

Ignition rod gap

is 3.5 to 4.0 mm

to pilot hood

YES

Replace ignition module.

Is ignition module

input voltage 1.1 to

2.1 VDC? (TEST 7)

Replace temperature controller.

YES

Is gas isolation valve

fully open?

Fully open gas isolation valve.

Is inlet gas pressure
within specification?

YES

Advise customer that inlet gas

pressure is not within

specification.

Refer to ‘Checking Inlet Gas Pressure’

in the ‘Component Adjustment

Procedures &

Checks’ section.

NG: 1.13 ~ 3.5 kPa

LPG: 2.75 ~ 3.5 kPa

YES

Is heater the correct

gas type for the

premises gas supply?

YES

1.2

YES

Refer to ‘DIP Switch Adjustments’

in the ‘Component Adjustment

Procedures &

Checks’ section.

Are temp controller

DIP switches 1 ~ 6 in

the correct position?

YES

Replace heater with a heater of

the correct gas type.

nsure DIP switches 1, 2 and

3 are in the OFF position

and

ensure DIP switches 4, 5 and 6

are in the correct position

according to heater model and

gas type

Содержание 834 Series






























































Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды

Rheem 834 Series, Инструкция по эксплуатации

Результаты поиска

Содержание 834 Series

Отзывы:

Похожие инструкции для 834 Series

Бренды по названию

Популярные бренды