RGB Spectrum Linx DVI Скачать руководство пользователя страница 23

Страница: 23 / 64

O P E R A T I O N

Command Line Operation

350-8794 V1.1

Linx DVI 8x8 Matix Switcher User’s Guide

. . . . .

RestoreFactoryDefaults

CAUTION

: Executing this command will

delete all presets and return all system parameters to their factory
default values.

UpdateFirmWare

- Installs firmware that has been uploaded to the

Linx

Switcher

. See

Chapter 5

for a full discussion on updating firmware.

COMMUNICATION

. . . . . . . . .

SETTINGS

Use of communications commands are discussed in

Chapter 2

. . . . . . . . .

SWITCH SETTINGS

Four commands can be used to set input/output values and to display
current parameters.

NAMEOUTput

- Use this command to assign an optional descriptive

name to the outputs. The system default is “Output #”

NAMEINput

- Use this command to assign an optional descriptive name

to the inputs. The system default is “Input #.”

ROUTE

- Assigns an input source to an output destination. A single

input can be routed to one or more output destinations.

OUTputENable

- Enables/disables one or all outputs.

OUTputSouRCe

- Associate an output to an input. An output can only

be associated with a single input.

INputEQualizer

- Compensate for the losses caused by the electrical

and physical characteristics of a DVI cable

. . . . . . . . .

PRESETS

Presets define specific input/output routing which can be loaded with a
single command. Presets are numbered 1 to 99. Preset commands are:

NAMEPreSeT

- Presets are referred to by number, but may be named;

issuing the command without a name argument displays the current
preset name.

SHoWPreSeT

- List the name and the input/output routing for a preset.

LiStPreSeT

- Lists the names of a range of presets.

DELetePreSeT

- Deleting a preset removes a name if present and all

input/output settings.

SaVePreSeT

- Save a single input-to-output routing or save the

complete current configuration.

RECALLPreSeT

- Load the input/output settings of a saved preset.

Содержание Linx DVI

































































Результаты поиска

Содержание Linx DVI

Отзывы:

Похожие инструкции для Linx DVI

Бренды по названию

Популярные бренды

RGB Spectrum Linx DVI, Руководство пользователя

Результаты поиска

Содержание Linx DVI

Отзывы:

Похожие инструкции для Linx DVI

Бренды по названию

Популярные бренды