Retigo Comfort 1011 Скачать руководство пользователя страница 48

Страница: 48 / 56

ENGLISH

7. TROUBLESHOOTING

The information shown below aims to help with
the identification and correction of any anomalies
and malfunctions which could occur during use.
Some of these problems can be resolved by the

user. For the others, precise skill is required and
they must therefore only be carried out by
qualified staff.

Problem

Causes

Solutions

The refrigerator unit does not start

No voltage

Check the power supply cable.

Check fuses.

Check the correct connection of the

appliance.

Other causes



If the problem persists,

contact the after-sales centre.



The refrigerator unit functions

continuously, cooling insufficiently

Room too hot

Air the environment

Dirty condenser

clean the condenser

Insufficient door sealing

check the gaskets

Insufficient quantity of

refrigerant gas



Contact the after-sales

centre.

Condenser fan at a standstill



Contact the after-sales

centre.

The refrigerator unit does not stop

Probe faulty



Contact the after-sales

centre.



Circuit board fault



Contact the after-sales

centre.



Presence of ice inside the

evaporator

Carry out a defrosting cycle possibly

with the door open.





If the problem persists,

contact the after-sales centre.



Appliance noise

Persistent vibrations

check there is no contact between

the appliance and other objects

inside or outside



Содержание Comfort 1011

























































Результаты поиска

Содержание Comfort 1011

Отзывы:

Похожие инструкции для Comfort 1011

Бренды по названию

Популярные бренды

Retigo Comfort 1011, Руководство по эксплуатации

Результаты поиска

Содержание Comfort 1011

Отзывы:

Похожие инструкции для Comfort 1011

Бренды по названию

Популярные бренды