Rethink Robotics Sawyer Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 220

Rethink Robotics Sawyer Скачать руководство пользователя страница 145

138

Intera 5.3

Sawyer and Safety

•

Subsystems:

•

Distributed Joint Controllers: Provide local “heartbeat” monitoring at each
joint, local joint disabling and braking capability.

•

Global Joint Disable/Braking: Implemented by the disruption of the
heartbeat signal.

•

Joint Position and Force Sensing Redundancy: Multiple sensors and
feedback mechanisms at each joint enable correlation of results to detect
failure.

•

Joint Controller Watchdog Timer: Self-monitoring disables motors and
applies brakes if an internal issue is detected with any joint or sensor.

5. Sensing and Behavior

•

Head Motion and Screen: Sawyer provides feedback on their status and
intentions, using their eyes during operation to signal intent by looking in the
direction of the next motion. This cue is intuitively picked up by nearby workers,
signaling what the robot will do next.

•

Motion Deactivated: Sawyer can be quickly and easily stopped by touching any
button, as if tapping a coworker on the shoulder.

•

Head-Mounted Lights: Sawyer has lights to signal status at a glance.

Rethink’s Collaborative Robot Regulatory Certifications

An application risk assessment, performed by the integrator and/or user, is a critical requirement to
ensure the proper use of Rethink's Collaborative Robots and the safety of personnel associated
with the robot’s application. The end effector and part must be evaluated as part of the application’s
task-based risk assessment. If either presents a hazard, safeguarding can be required. For
example, a risk assessment for an application where Sawyer would be handling “knives” or sharp-
edged objects would result in excluding collaborative operation and using Sawyer as a typical
machine that is safeguarded.

Sawyer complies with applicable requirements in ISO 10218-1:2011 as supplemented by ISO/TS
15066 for collaborative robots and provides E-stop and protective stop functions meeting
requirements in ISO 13849-1:2006, Cat. 3 / PL d. Sawyer meets applicable requirements for
electrical, fire & mechanical hazards in IEC 61010-1:2010 (including all country deviations in the CB
Scheme), and EMC requirements in IEC 61326-1:2013.

«
...
143
144
145
146
147
...
»

Содержание Sawyer





























































































































































































































Отзывы:

Нет отзывов