Renesas 7542 Скачать руководство пользователя страница 62

Страница: 62 / 139

7542 Group

Rev.3.02 Oct 31, 2006 Page 62 of 134
REJ03B0006-0302

●

On-chip oscillation division ratio

At on-chip oscillator mode, division ratio of on-chip oscillator for

CPU clock is selected by setting value of on-chip oscillation divi-

sion ratio selection register. The division ratio of on-chip oscillation

for CPU clock is selected from among 1/1, 1/2, 1/8, 1/128. The op-

eration clock for the peripheral function block is not changed by

setting value of this register.

■

Notes on On-chip Oscillation Division Ratio

• When system is released from reset, R

OSC

/8 (on-chip oscillator

middle-speed mode) is selected for CPU clock.

• When state transition from the ceramic or RC oscillation to on-

chip oscillator, R

OSC

/8 (on-chip oscillator middle-speed mode)

is selected for CPU clock.

• When the MCU operates by on-chip oscillator for the main clock

without external oscillation circuit, connect X

pin to V

through a resistor and leave X

OUT

pin open.

Set “10010x00

” (x = 0 or 1) to CPUM.

Fig. 78 Structure of on-chip oscillation division ratio selection register

On-chip oscillation division ratio selection register
(RODR: address 0037

, initial value: 02

)

On-chip oscillator division ratio

b1 b0

0 0: On-chip oscillator double-speed mode (R

OSC

/1)

0 1: On-chip oscillator high-speed mode (R

OSC

/2)

1 0: On-chip oscillator middle-speed mode (R

OSC

/8)

1 1: On-chip oscillator low-speed mode (R

OSC

/128)

Not used (returns “0” when read)

b7 b0

Содержание 7542












































































































































Результаты поиска

Содержание 7542

Отзывы:

Renesas 7542, Руководство пользователя, Страница: 62 / 139

Результаты поиска

Содержание 7542

Отзывы: