Reliance electric GV3000 Скачать руководство пользователя страница 51

Страница: 51 / 91

Digital Input Connections (Terminals 1625)

Terminal 16: +24 VDC (Current Limited) (For remote control digital inputs only)

Terminal 17: Digital Input 8 (Remote/Local) Programmable

Terminal 18: Digital Input 7 (Ramp1/Ramp2) Programmable

Terminal 19: Digital Input 6 (Forward/Reverse) Programmable

Terminal 20: Function Loss

Terminal 21: Run/Jog

Terminal 22: Reset

Terminal 23: Stop

Terminal 24: Start

Terminal 25: +24 VDC Common

When a userinstalled function loss input, a coasttostop pushbutton, or another external interlock is

installed, the factorinstalled jumper connecting terminals 16 and 20 (or 16A and 20A) must be

removed so that a contact will open to stop the drive.
Terminals 17, 18, and 19 (remote control inputs 8, 7, and 6) are programmed using parameters P.007,

P.008, and P.031 through P.038. Factory default settings are shown here in parentheses. Refer to the

GV3000 Programming Manual (D23339) for more information.

Snubber Resistor Braking Connections (Terminals 26 and 27)

Terminal 26: Snubber Resistor Braking Signal (125HP Drives only)

Terminal 27: +24 VDC Common

Status Relay Connections (Terminals 2831)

Terminal 28: N.C Relay Contact

Terminal 29: N.C. Relay Common

Terminal 30: N.O. Relay Contact

Terminal 31: N.O. Relay Common

Relay contact closure is programmable through parameter P.013. Refer to the GV3000 Programming

Manual (D23339) for more information.

StockCheck.com

Downloaded from StockCheck.com

Содержание GV3000


























































































Результаты поиска

Содержание GV3000

Отзывы:

Похожие инструкции для GV3000

Бренды по названию

Популярные бренды

Reliance electric GV3000, Инструкция по эксплуатации

Результаты поиска

Содержание GV3000

Отзывы:

Похожие инструкции для GV3000

Бренды по названию

Популярные бренды