Reliance electric GV3000 Скачать руководство пользователя страница 25

Страница: 25 / 91

215

2.7.3 RS232 Communication Port

The Regulator board contains a 9pin Dshell RS232 communication port (J8). This port provides

RS232 communication between the GV3000 drive and a personal computer running the Control and

Configuration (CS3000) software. See figures 2.8 and 2.9. Refer to instruction manual D23348, for

more information.

2.7.4 Option Board Connector

The flatribbon cable connector (J3) on the left side of the Regulator board is a parallel bus

connection port that provides a means of attaching optional boards such as the DeviceNet board, the

RMI board, or the AutoMax Network Communication board to the GV3000 drive. See figures 2.8

and 2.9. The option board is mounted below the Regulator board inside the drive. Refer to the

appropriate board instruction manual for more information. Refer to section 2.7 of this manual for

more information on optional drive kits.

2.7.5 Operator Interface Module Connector

Flatribbon connector J7 provides a means of attaching the optional Operator Interface module

(OIM). The OIM is available for use as a remote keypad for the GV3000.

2.7.6 Keypad/Display

The front panel keypad/display is used to program and operate the GV3000 drive. See figure 2.13.

Refer to instruction manual D23339 for more information.

1. When this LED is on, parameters cannot be modified

from the keypad without entering the correct password
into P.051 (Programming Disable).

1. Stops the drive.
2. Resets faults.

1. Applies power to the motor if the

keypad is selected as the control source.

Figure 2.13 Keypad/Display

StockCheck.com

Downloaded from StockCheck.com

Содержание GV3000


























































































Результаты поиска

Содержание GV3000

Отзывы:

Похожие инструкции для GV3000

Бренды по названию

Популярные бренды

Reliance electric GV3000, Инструкция по эксплуатации

Результаты поиска

Содержание GV3000

Отзывы:

Похожие инструкции для GV3000

Бренды по названию

Популярные бренды