Regency Panorama P33CE-LP11 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 76

background image

24

|

P33CE-11 Direct Vent Gas Fireplace

installation

Venting Introduction

The P33CE uses the "balanced flue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside
combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

There are 5 vent systems approved for use with the P33CE: the Regency

®

Direct Vent Flex System for Horizontal Terminations only and the Simpson Dura-

Vent Pro, Selkirk Direct-Temp, Amerivent Direct Vent, Metal-Fab Sure Seal, Security Secure Vent and ICC Excel Direct for Horizontal and Vertical Terminations
(see following "Venting" Sections for more details).

Note: These flue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel
or gas burning appliance. Each direct vent gas appliance must use its own separate vent system. Common vent systems are prohibited. (See "Rigid Pipe
Venting System" for more details and exceptions).

NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.

«
...
22
23
24
25
26
...
»

Содержание Panorama P33CE-LP11













































































Отзывы:

Нет отзывов

Похожие инструкции для Panorama P33CE-LP11

Бренд: Waterford Страницы: 24

Бренд: baltur Страницы: 76

Бренд: Verine Страницы: 19

Simplifyre SFE-ST

Бренд: Hearth and Home Technologies Страницы: 8

Ecosmart Fire BK Series

Бренд: MAD Страницы: 14

Бренд: CobraCo Страницы: 4

Бренд: HOMEDEPOT Страницы: 4

Бренд: Heat & Glo Страницы: 2

Бренд: Regency Fireplace Products Страницы: 44

Relaxed M Smart

Бренд: Faber Страницы: 30

Бренд: Oblica Страницы: 10

Salzburg XL Series

Бренд: Nordpeis Страницы: 72

Бренд: Modern Flames Страницы: 2

Бренд: WANDERS Страницы: 52

Бренд: WANDERS Страницы: 68

Бренд: Wamsler Страницы: 60

H38SVO-ST Series

Бренд: Montigo Страницы: 20

4915 Illuminations LED

Бренд: Illuminations Electric Fireplace Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды