Regency Panorama P33CE-LP11 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 76

background image

P33CE-11 Direct Vent Gas Fireplace

|

43

installation

Gas Pipe Pressure
Testing

The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-
off valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 1/2 psig. (3.45 kPa). Disconnect piping
from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.

1)

Make sure the switch is in the "OFF" position.

2)

Loosen the "IN" and/or "OUT" pressure tap(s),

turning counterclockwise with a 1/8" wide flat
screwdriver.

3)

Attach manometer to "IN" and/or "OUT"

pressure tap(s) using a 5/16" ID hose.

4)

Light the pilot by turning the switch to "ON"

position.

5)

The pressure check should be carried out with

the unit burning and the setting should be within
the limits specified on the safety label.

6)

When finished reading manometer, turn off the

gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" flat screwdriver.

Note: Screw should be snug, but do not
over tighten.

High Elevation

This unit is approved in Canada for altitude to
4500 ft. (CAN/CGA-2.17-M91). For Natural Gas
installations above 4500 ft. follow current CAN/
CGA-B149.1.

Pilot Adjustment

Periodically check the pilot flames. Correct

Note: If you have an incorrect flame

pattern, contact your Regency

®

dealer for further instructions.

Incorrect flame pattern will have small,
probably yellow flames, not coming into
proper contact with the rear burner or flame
sensor.

Burner

Flame Sensor

Pilot

Ignitor

flame pattern has two strong blue flames:
1 flowing around the flame sensor and 1
flowing across the burner (it does not have
to be touching the burner).

P33CE-NG11 System Data

Burner Inlet Orifice
Sizes:

#44

Max. Input Rating

20,000 Btu/h

Min. Input Rating

14,000 Btu/h

Supply Pressure

min.5.0" w.c.

Manifold Pressure (High)

3.5"w.c.(0.87kPa)

Manifold Pressure (Low)

1.6"w.c.(0.39kPa)

P33CE-LP11 System Data

Burner Inlet Orifice
Sizes:

#55

Max. Input Rating

19,500 Btu/h

Min. Input Rating

15,500 Btu/h

Supply Pressure

min.11.0" w.c.

Manifold Pressure
(High)

10" w.c. (2.49kPa)

Manifold Pressure
(Low)

6.4" w.c. (1.59kPa)

885 S.I.T. Valve Description

1)  6 Stage flame adjustment
2)  Pilot adjustment
3)  Outlet Pressure Tap
4)  Inlet Pressure Tap
5)  Pilot Outlet
6)  Main Gas Outlet
7)  Main Gas Inlet

1

2

3

4

6

5

7

1

2

3

4

6

5

7

«
...
41
42
43
44
45
...
»

Содержание Panorama P33CE-LP11













































































Отзывы:

Нет отзывов

Похожие инструкции для Panorama P33CE-LP11

Бренд: Jøtul Страницы: 104

Бренд: Paloform Страницы: 18

CANTERBURY CANTIB-02-LP

Бренд: Cannon Страницы: 12

Бренд: Majestic Страницы: 40

34 Zircon Direct Vent

Бренд: Malm Fireplaces Страницы: 58

CHIMENEA SRCH06D

Бренд: BIGHORN Страницы: 8

Бренд: FocalPoint Страницы: 11

Бренд: FMI Страницы: 40

Бренд: Sunbeam Страницы: 20

FP-7-LM ANTOINETTE

Бренд: Valcourt Страницы: 2

Бренд: Stûv Страницы: 16

Бренд: C&J Страницы: 24

Бренд: Century Страницы: 26

Бренд: Majestic Страницы: 24

Бренд: GlammFire Страницы: 24

Бренд: Cosi Страницы: 29

Бренд: Cosi Страницы: 30

Бренд: Arada Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды