Regency Panorama P33CE-LP11 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 76

background image

46

|

P33CE-11 Direct Vent Gas Fireplace

installation

Note: The logs must not be in the unit.

3)

Insert the back brick panel by carefully

slipping it between the back wall of the
firebox and the rear log bracket.

Optional Brick
Panels

1)

Remove the safety screen and glass door.

Remove logs.

2)

Attach the 2 Rear Brick Retaining clips to the

rear wall. Loosen the screws in the top and rear
wall of the firebox and slide the retaining clips
into position (tight against the firebox top) and
then tighten the screws.

4)

Put the side panels in next. Slide them in from

the front and push them flat up against the
wall. Be very careful not to scratch them on the
firebox hardware.

5)

Slide the Top Brick Panel into position and slide

the Top Brick Retaining clips so that they hold
the Top Brick Panel in place and tighten down
the screws.

Log Set Installation

Notch

Bracket

Bracket

250

254

Vermiculite

Vermiculite

Vermiculite

250

254

The 3-digit numbers (i.e. 250) are
molded into the rear of each log.

Read the instructions below carefully
and refer to the diagrams. If logs
are broken do not use the unit until
they are replaced. Broken logs can
interfere with the pilot operation.

Log Kit # 431-930 contains the

following pieces:

A) 250

Rear Log

B) 254

Middle Cross Log

C) 253

Front Left Cross Log

D) 251

Rear Left Log

E) 252

Front Right Cross Log

F)

Embers

902-156

G)

Vermiculite

902-179

H)

Rock Wool

902-153

I)

Platinum Embers 946-669

(supplied with packaged manual)

NOTE: If you will be installing the op-

tional Brick Panels, install the

Brick Panels prior to installing

the logs.

1) Carefully remove the logs from the box and

unwrap them. The logs are fragile, handle

with care -

do not force into position.

2) Sprinkle the vermiculite and embers around

the firebox base.

3) Place the Log 250 on the rear log support

pins with the flat side to the back.

4) Place Log 254 on the front right side of the

burner. Push the back of the log against
the 2 brackets with the notch on the bottom
right side of the log fitting into the right side
of the grate.

5) Position Log 253 across the cutouts in

Logs 250 and 254 with the notch on the
left side of the log fitting into the 2nd grate
tab.

Cutouts

2nd Grate Tab

253

250

254

D) 251

A) 250

C) 253

B) 254

E) 252

«
...
44
45
46
47
48
...
»

Содержание Panorama P33CE-LP11













































































Отзывы:

Нет отзывов

Похожие инструкции для Panorama P33CE-LP11

Бренд: Vantage Hearth Страницы: 36

Бренд: Vantage Hearth Страницы: 32

Бренд: Majestic Страницы: 4

Бренд: pleasant hearth Страницы: 52

Бренд: Regal Flame Страницы: 10

Бренд: Dimplex Страницы: 64

Бренд: Ravelli Страницы: 9

Бренд: Comfort Flame Страницы: 70

Бренд: KEKAI Страницы: 18

Бренд: Continental Fireplaces Страницы: 28

Kingsman ZDV3624NB

Бренд: R-Co Страницы: 30

ECOFIRE VIVIENNE

Бренд: Palazzetti Страницы: 148

Бренд: Napoleon Страницы: 132

Бренд: Nordpeis Страницы: 72

Бренд: Coleman Страницы: 16

Бренд: Kinder Страницы: 28

Бренд: Modern Flames Страницы: 2

Бренд: GlammFire Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды