Regency Liberty LRI4E series Скачать руководство пользователя страница 1

Страница: 1 / 72

Liberty® LRI4E / Regency Horizon® HRI4E

Gas Insert

Owners &

Installation Manual

www.regency-fire.com

Horizon

HRI4E

Liberty

LRI4E

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS
•

Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

WARNING
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

MODELS: LRI4E-NG11 Natural Gas LRI4E-LP11 Propane
HRI4E-NG11 Natural Gas HRI4E-LP11 Propane

919-933c

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

03.28.19

Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.

Tested by:

Certified to/Certifié pour: CSA 2.17-2017
ANSI Z21.88-2017
CSA 2.33-2017

Содержание Liberty LRI4E series









































































Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды

Regency Liberty LRI4E series, Инструкция для владельца и по установке

Результаты поиска

Содержание Liberty LRI4E series

Отзывы:

Похожие инструкции для Liberty LRI4E series

Бренды по названию

Популярные бренды