background image

8

 | 

Regency Horizon HZ30E-10 Gas Fireplace

 | 

8

installation

4.  This  appliance  must  be  connected  to  the 

specified vent and termination cap to the outside 
of the building envelope. Never vent to another 
room or inside a building. Make sure that the 
vent is fitted as per Venting instructions.

5.  Inspect the venting system annually for blockage 

and any signs of deterioration.   

6.  Venting terminals shall not be recessed into a 

wall or siding.

7.  Any safety glass removed for servicing must be 

replaced prior to operating the appliance.

8.  To prevent injury, do not allow anyone who is 

unfamiliar with the operation to use the fireplace.

9.  Wear gloves and safety glasses for protection 

while doing required maintenance.

10. Be aware of electrical wiring locations in walls 

and ceilings when cutting holes for termination.

11.     Under  no  circumstance  should  this 

appliance  be  modified.    Parts  that  have 
to  be  removed  for  servicing  should  be 
replaced prior to operating this appliance. 
    

12.  Installation  and  any  repairs  to  this 
appliance should be done by a qualified service 
person. A professional service person should be 
called to inspect this appliance annually. Make 
it a practice to have all of your gas appliances 
checked annually.

13. Do not slam shut or strike the glass door.

14. Under no circumstances should any solid fuels 

(wood, paper, cardboard, coal, etc.) be used in 
this appliance.

15. The appliance area must be kept clear and free 

of combustible materials, (gases and other flam-
mable vapours and liquids).

Emissions from burning  wood or gas could 
contain  chemicals  known  to  the  State  of 
California to  cause cancer, birth defects or 
other reproductive harm.

IMPORTANT MESSAGE  

SAVE THESE 

INSTRUCTIONS

The Gas Fireplace must be installed in accordance 
with  these  instructions.  Carefully  read  all  the 
instructions in this manual first. Consult the "authority 
having jurisdiction" to determine the need for a permit 
prior to starting the installation. It is the responsibility 
of the installer to ensure this fireplace is installed 
in compliance with manufacturers instructions and 
all applicable codes.

BEFORE YOU  START

Safe  installation  and  operation  of  this  appliance 
requires common sense, however, we are required 
by  the  Canadian  Safety  Standards  and  ANSI 
Standards to make you aware of the following:

CLOTHING OR OTHER FLAMMABLE 
MATERIAL SHOULD NOT BE PLACED 
ON OR NEAR THE APPLIANCE.

   

CHILDREN AND ADULTS SHOULD BE 
ALERTED TO THE HAZARDS OF HIGH 
SURFACE TEMPERATURES,  ESPE-
CIALLY THE FIREPLACE GLASS, AND 
SHOULD STAY AWAY TO AVOID BURNS 
OR CLOTHING IGNITION.  

GENERAL SAFETY  

INFORMATION

1.  The  appliance  installation  must  conform  with 

local codes or, in the absence of local codes, with 
the current Canadian or National Gas Codes, 
CAN1-B149 or ANSI Z223.1 Installation Codes.

2.  The  appliance  when  installed,  must  be 

electrically grounded in accordance with local 
codes, or in the absence of local codes with the 
current National Electrical Code, ANSI/NFPA 70 
or CSA C22.1 Canadian Electrical Code.

3.  See  general  construction  and  assembly 

instructions. The appliance and vent should be 
enclosed.

INSTALLATION AND REPAIR SHOULD 
BE DONE BY AN AUTHORIZED 
SERVICE PERSON. THE APPLIANCE 
SHOULD BE INSPECTED BEFORE 
USE AND AT LEAST ANNUALLY BY A 
PROFESSIONAL SERVICE PERSON. 
MORE FREQUENT CLEANING MAY 
BE REQUIRED DUE TO EXCESSIVE 
LINT FROM CARPETING, BEDDING 
MATERIAL, ETC. IT IS IMPERATIVE THAT 
CONTROL COMPARTMENTS, BURNERS 
AND CIRCULATING AIR PASSAGEWAYS 
OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE 
APPLIANCE SHOULD BE LOCATED 
OUT OF TRAFFIC AND AWAY FROM 
FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS 
APPLIANCE CORRECTLY WILL VOID 
YOUR WARRANTY AND MAY CAUSE A 
SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CARE-
FULLY  SUPERVISED WHEN THEY ARE 
IN THE SAME AREA AS THE APPLI-
ANCE.  TODDLERS, YOUNG CHILDREN 
AND OTHERS MAY BE SUSCEPTIBLE 
TO ACCIDENTAL CONTACT BURNS.  A 
PHYSICAL BARRIERS IS RECOMMEND-
ED IF THERE ARE AT RISK INDIVIDUAL 
IN THE HOUSE.  TO RESTRICT ACCESS 
TO A FIREPLACE OR STOVE, INSTALL 
AN ADJUSTABLE SAFETY GATE TO 
KEEP TODDLERS, YOUNG  CHILDREN 
AND OTHER AT RISK INDIVIDUALS OUT 
OF THE ROOM AND AWAY FROM HOT 
SURFACES. 

A BARRIER DESIGNED TO REDUCE 
THE RISK OF BURNS FROM THE HOT 
VIEWING GLASS IS PROVIDED WITH 
THIS APPLIANCE AND SHALL BE 
INSTALLED FOR THE PROTECTION 
OF CHILDREN AND OTHER AT-RISK 
INDIVIDUALS 

IF THE BARRIER BECOMES DAMAGED, 
THE BARRIER SHALL BE REPLACED 
WITH THE MANUFACTURER'S BARRIER 
FOR THIS APPLIANCE.

ANY SAFETY SCREEN, GUARD, OR 
BARRIER REMOVED FOR SERVICING 
AN APPLIANCE  MUST BE REPLACED 
PRIOR TO OPERATING THE APPLIANCE.

Содержание Horizon HZ30E

































































Отзывы: