Regency Horizon HZ30E Скачать руководство пользователя страница 38

Страница: 38 / 64

Regency Horizon HZ30E-10 Gas Fireplace

installation

OPTIONAL FAN INSTALLATION

120 Volt AC power is needed for the fan. The fan can be hard wired if desired.

The outlet should be installed in the receptacle box on the right hand side by a

qualified electrician. The neutral (wider) slot of the polarized outlet should be at

the top.

Unit must be grounded at all times. Do not cut the ground terminal off

under any circumstances.

Follow these instructions before the

initial installation

into the framing. If

installing the optional fan into an existing installation see the instructions on the

following pages.

1. Remove the 2 screws and remove the front access panel.

2. Slide the fan through the front access panel into the lower right corner at the

base of the unit. Secure the fan to the base with 2 screws

3. Attach the green ground wire to the ground lug – located in the lower left back

corner of the unit.

4. Slide the thermodisc/cover assembly on to the bracket clip on the bottom of

the unit. Ensure no wires will touch the hot surfaces.

The fan control module (supplied with the fan kit) secures to the floor of the

unit with a Velcro pad. The front of the fan control module should face to the

left directly in front of the fan. Plug the fan control module into the outlet in the

unit.

5. Plug in the fan power cord to the Fan Control Module into the outlet marked

“Fan”. Plug the FCM-COM wire from the remote control wiring harness into the

location on the Fan Control Module marked “COM”. Turn the switch on the

Fan Control Module to the ON position. ON is to the left. The “O” is the off

position

6. Reinstall the access panel removed in step 1.

Note:

The HZ30-10 does not have BTU turndown therefore this feature is

inactive on the GTMF remote.

TO REMOVE THE FAN

Turn the power off.

Reverse the above instructions

MAINTENANCE:

The sealed bearings are lubricated so there is no need to

lubricate them further. Extra lubricant will cause more lint to and dust to build

up causing the premature failure of the bearings.

Regular cleaning and vacuuming of the fan area will add to the life of the

motor

Screw Locations

IMPORTANT:

These fans collect a lot of dust from within your home.

Ensure you maintain these fan motors on a regular

basis by vacuuming the fan blades and the housing with

a soft brush nozzle.

Содержание Horizon HZ30E

































































Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды

Regency Horizon HZ30E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды