Regency Horizon HZ30E Скачать руководство пользователя страница 23

Страница: 23 / 64

Regency Horizon HZ30E-10 Gas Fireplace

installation

Notes:

1. Liner sections should be continuous without any

joints or seams.

2. Only Flex pipe purchased from Regency

may be

used for Flex installations

3. Horizontal vent must be supported every 3 feet.

4. Regency

Direct Vent System (Flex) is only approved

for horizontal terminations.

5. Flex system can only be used up to a maximum

continuous vent length of up to 10 feet. If longer
runs are required, rigid pipe must be used.

6-7/8"

(173mm)

dia. Flue pipe

4" dia. flue pipe

spring spacer

Wall Thimble

Termination Cap

(Part# 946-523/P)

AstroCap

HORIZONTAL TERMINATIONS

FLEX VENT 4" X 6-7/8

These venting systems, in combination with the HZ30E Direct Vent Gas Fireplace, has been tested and listed as a direct vent heater system by Warnock

Hersey/ Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent Termination

Locations" section.

Regency

Direct Vent (Flex) System Termination Kits includes all the parts needed to install the HZ30E using a flexible vent.

FPI Kit #

Length

Contains:

#946-513

2 Feet

6-7/8” flexible outer liner (Kit length)

4” flexible inner liner (Kit length)

spring spacers

thimble

AstroCap

termination cap

screws

tube of Mill Pac

plated screws

S.S. screws #8 x 1-1/2” drill point

#946-515

4 Feet

#946-516

10 Feet

Содержание Horizon HZ30E

































































Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды

Regency Horizon HZ30E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды