Regency Horizon HZ30E Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

background image

Regency Horizon HZ30E-10 Gas Fireplace

|

13

|

13

installation

WALL MOUNT ON / OFF SWITCH AND RECEIVER INSTALLATION

REQUIRED FOR ALL INSTALLATIONS - INCLUDING PROFLAME REMOTE CONTROLS

* Installation of the Receiver must be completed before installing facing materials.

J-Box

Receiver

Wall Plate

Slider Switch

Low Voltage Junction Box

12 pin connector - located

on outer right side of the

firebox.

I

MPORTANT INSTALLATION NOTE:

The Receiver must be placed inside the supplied (Low Voltage)

junction type wall box and installed into the wall only.

DO NOT INSTALL WITHIN THE CONFINES OF THE FIREPLACE.

Wall Mounting

1. Install the junction box to the framing, at desired location within 10 ft. from fireplace.

2. Feed the 12 pin connector through the opening at back of junction box.
3. Connect the 12 pin connector to the back of the receiver.

4. Install the Receiver in the Low Voltage Junction box, supplied with HZ30E.

5. Insert the 4 AA type batteries in the battery compartment with the correct polarity.

6. Place the slider into the cover plate.

7. Put the Receiver switch in the “OFF” position, to allow correct lineup for slider switch.
8. Make sure the Receiver and cover plate words “ON” and “UP” are on the same side.

9. Align the slider with the switch on the Receiver and couple the switch into the slider.
10. Align the screw holes.
11. Using the two (2. screws provided secure the cover plate to the Receiver.

«
...
11
12
13
14
15
...
»

Содержание Horizon HZ30E

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ30E

Бренд: Verine Страницы: 19

Бренд: PSF Страницы: 2

Бренд: Empire Comfort Systems Страницы: 66

Бренд: Napoleon Страницы: 2

Maestro 60/2 Tall RCH

Бренд: Dru Страницы: 68

Бренд: Contempo Страницы: 10

Бренд: HAMPTON BAY Страницы: 7

Бренд: Astria Страницы: 44

Бренд: Valor Страницы: 14

Бренд: Napoleon Страницы: 52

ClassicFlame 26MM2209

Бренд: Twin-Star International Страницы: 24

Бренд: Febo Страницы: 16

Бренд: Charlton & Jenrick Страницы: 28

Бренд: Vanguard Страницы: 32

Бренд: Enviro Страницы: 41

Madison Park MPI27

Бренд: IronStrike Страницы: 40

Бренд: Mason-Lite Страницы: 24

Бренд: St. Croix Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды