Regency Horizon HZ30E Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 64

background image

42

|

Regency Horizon HZ30E-10 Gas Fireplace

|

42

installation

REFLECTIVE PANEL INSTALLATION

918-901a

05/16/13

1)

Remove the faceplate and glass door if already installed - see

manual for instructions.

2)

Install the back panel fi rst. Tilt the panel forward - position the bottom
of the panel fi rst. Use care not to scratch or mar the panel on the
pilot shield.

3)

Install the left side panel - secure in position with one panel clip and
one screw, as shown in the diagram below.

4)

Install the right side panel - secure in position with one panel clip
and one screw.

5)

Reinstall glass door - reinstall faceplate.

6)

Final installation

1

HZ30E

REFLECTIVE PANEL INSTALLATION

Before installation, panels must be handled and cleaned as per instructions noted below:

Black Enamel Panels

•

Black Enamel panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time.

Claims for damage after installation will not receive consideration.

•

Black Enamel panels will discolor a little during normal operation. This is normal and should not be considered a defect.

*

All hand and fi nger marks

MUST

be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any

fi ngerprints before applying heat to the unit.

Failure to do this will result in burn stain on panels which you will be unable to remove.

Not protected by product warranty.

«
...
40
41
42
43
44
...
»

Содержание Horizon HZ30E

































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ30E

Бренд: Quadra-Fire Страницы: 28

Бренд: Majestic Страницы: 4

Бренд: baltur Страницы: 76

Signature 0346217

Бренд: Mimosa Страницы: 12

Бренд: Uniflame Страницы: 2

Бренд: Scott Living Страницы: 27

Бренд: Firesense Страницы: 8

Бренд: Heat & Glo Страницы: 64

"Zero Clearance" ZDV1001

Бренд: Kingsman Страницы: 16

Бренд: Napoleon Страницы: 60

Бренд: Wamsler Страницы: 84

Бренд: Member's Mark Страницы: 22

BATHYSCAFOCUS Hublot

Бренд: Focus Страницы: 14

Бренд: Focus Страницы: 20

Бренд: FocalPoint Страницы: 4

F820590 FPFBQ392

Бренд: FocalPoint Страницы: 4

Бренд: FocalPoint Страницы: 7

PANORAMIC COMPLETE ELECTRIC SUITE

Бренд: Focal Point Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды