Regency Horizon HZ30E Скачать руководство пользователя страница 55

Страница: 55 / 64

Regency Horizon HZ30E-10 Gas Fireplace

maintenance

VALVE ASSEMBLY REPLACEMENT

4. Remove the mesh barrier (see manual) and glass door.

a) Remove the 2 screws shown below at the bottom of the glass
door

b) Swing the door out 45

from the bottom and lift up and out.

Location of screws on access plate

1. Turn the unit off and allow it to cool down to room temperature.

2. Shut off the gas and power supply to the unit.

3. Remove the faceplate (see detailed instructions in this manual).

5. Remove the burner tray cover by lifting up and out as shown below.

* Prior to removing burner - remove crystals, pebbles, spa stones and inner

panels - if installed.

6. Loosen 2 screws at the back of the burner to release it.

7. Remove the burner by sliding it to the right - then lift out.

8. Remove the valve access plate by undoing the 17 outer screws - see

locations below.

Содержание Horizon HZ30E

































































Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды

Regency Horizon HZ30E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ30E

Отзывы:

Похожие инструкции для Horizon HZ30E

Бренды по названию

Популярные бренды