Regency City 686-927 Скачать руководство пользователя страница 92

Страница: 92 / 124

92 | City Series CB60E-1

installation

Inner Black Enamel Panel Installation

10.30.19

920-173

CB60E

BLACK ENAMEL INNER PANEL INSTALLATION

919-898

08.14.18

CB60E ENAMEL PANEL INSTALLATION

Black Enamel Panels — Handling Instructions

•

Black Enamel panels must be inspected for scratches and dimples prior to installation.

All claims to be recorded at this time.

Claims for damage after installation will not receive consideration.

•

Black Enamel panels will discolor a little during normal operation. This is normal and should not be considered a defect.

All hand and fi nger marks

MUST be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any fi ngerprints before

applying heat to the unit.

Failure to do this will result in burn stain on panels which you will be unable to remove.

*Not protected by product warranty.

The CB60E has optional enamel inner panels that may be installed.
CB60E outer panels and 8 inner panels.

Turn off power and gas to unit and allow to cool to room temperature. Remove
the safety glass and fi rebox glass — see manual for instructions

CB60E OUTER PANELS

1. Install 5 inner base panels as shown.

2. On back of fi rebox wall--install 6 screws (loosely) in locations shown

below. Install 3 back panels--hang panels on installed screws through
keyhole opening.

3. Reinstall fi rebox glass - see instructions in manual.

1. Install outer side panel as shown below.

2. Install glass stopper (if desired) by sliding down the outside of the
outer side panel.

CITY SERIES

CB60E-1 OUTER PANELS

The CB60E-1 has optional enamel inner panels that may be installed.

CB60E-1 outer panels and 8 inner panels.

Содержание City 686-927





























































































































Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды

Regency City 686-927, Инструкция для владельца и по установке

Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды