Regency City 686-927 Скачать руководство пользователя страница 82

Страница: 82 / 124

82 | City Series CB60E-1

installation

Inner Glass Panel (Firebox Glass) Installation / Removal

1. Remove outer safety barrier glass panels if previously installed–see instruc-

tions in this manual.

2. Remove outer panels installed in unit - see panel removal section in this manual.

3. From the front inside lower panel of the unit--pivot the 3 glass supports

into upright position as shown below.

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the manufac-

turer. Lower the glass to rest in a safe place, this is to prevent damage to

the glass edges. Extra care must be taken when removing/installing the

glass. Breakage or damage to the edge of the glass which occurs as a result

of careless handling will not be covered under warranty.

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant

surface to place the 70-3/8"x 15-1/4" glass

• Never clean or remove hot glass

Note: The suction cups may leave a round film on the

glass when used. Ensure that the glass is cleaned using

a fireplace glass cleaner after each removal and prior to

operating the appliance.

Note:

glass panels must be installed to operate fireplace

glass supports

4. Open the 8 clamps at the top of the glass.

Handle glass with supplied vacuum clamps

Glass supports in upright position

Clamps in closed position

Press glass vacuum clamps in open position firmly onto surface of glass.

Bring handles together to close.

Open

Closed

Note: The following installation diagrams do not include

the vacuum clamps but it is strongly recommended

to use clamps at all times when handling the firebox

glass.

Glass removal video

With the top clamps in open position, use your hands to pull the

two glass gasket rails towards you.

Clamps in open position, rail

pulled forward

Содержание City 686-927





























































































































Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды

Regency City 686-927, Инструкция для владельца и по установке

Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды