Regency City 686-927 Скачать руководство пользователя страница 83

Страница: 83 / 124

City Series CB60E-1 | 83

installation

Levers to lower firebox glass

tooltip

6. Support the glass with one hand and open the 9 lower clamps.

5. Pull the 3 lower glass gasket pads forward to release the glass.

7. Locate the 2 levers below the glass and turn them both 90° in a clockwise

direction to lower the firebox glass panel.

8. Carefully lean glass forward onto supports.

Glass panel--leaning on supports

Lower clamps (x9) in open position

Push down on levers to lower glass panel

Gasket pad

NOTE:

The firebox glass may remain propped on the glass supports to clean

the interior surface. Use care when cleaning -- do not apply excessive force

or pressure.

To remove the firebox glass panel from the unit:

tilt the glass forward

gently onto the glass supports, grip both suction clamps and lift the glass

up and out of the unit.

10. To install glass--reverse steps.

IMPORTANT:

Remove glass panel completely when installing or removing

panels, logs, media, etc. to avoid causing any damage to the glass.

Содержание City 686-927





























































































































Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды

Regency City 686-927, Инструкция для владельца и по установке

Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды