Regency City 686-927 Скачать руководство пользователя страница 25

Страница: 25 / 124

City Series CB60E-1 | 25

owner's information

Inner Glass Panel Installation / Removal

1. Remove outer safety barrier glass panels if previously installed–see instruc-

tions in this manual.

2. Remove outer panels installed in unit - see panel removal section in this manual.

3. From the front inside lower panel of the unit--pivot the glass support into

upright position as shown below.

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the

manufacturer. Lower the glass to rest in a safe place, this is to

prevent damage to the glass edges. Extra care must be taken when

removing/installing the glass. Breakage or damage to the edge of

the glass which occurs as a result of careless handling will not be

covered under warranty.

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant

surface to place the 60-3/8"x 18-1/4" glass

• Never clean or remove hot glass

Note: The suction cups may leave a round film on the

glass when used. Ensure that the glass is cleaned using

a fireplace glass cleaner after each removal and prior to

operating the appliance.

Note: glass panels must be installed to operate fireplace

4. Open the 8 clamps at the top of the glass.

Handle glass with supplied vacuum clamps

Glass supports in upright position

Clamps in closed position

With the top clamps in open position, use your hands to pull the

two glass gasket rails towards you.

Clamps in open position, rail

pulled forward

Press glass vacuum clamps in open position firmly onto surface of glass.

Bring handles together to close.

Open

Closed

Note--the following installation diagrams do not include the

vacuum clamps but it is strongly recommended to use

clamps at all times when handling the firebox glass.

Glass removal video

Содержание City 686-927





























































































































Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды

Regency City 686-927, Инструкция для владельца и по установке

Результаты поиска

Содержание City 686-927

Отзывы:

Похожие инструкции для City 686-927

Бренды по названию

Популярные бренды