Regency Fireplace Products P90-LP10 Скачать руководство пользователя

Страница: 29 / 52

Regency Excalibur

P90-10 Zero Clearance Direct Vent Gas Fireplace

installation

Diagram 4

The arrow on the vent cap should

be pointing up.

Insure that the 1-1/2"

clearances to combustible materials

are maintained (Diagram 4.. Install the

termination cap.

NOTE: For Snorkel terminations in ABOVE

grade installations, follow national

or local code requirements.

Below Grade Installation

If the Snorkel Termination must be installed

below grade, i.e. basement application, proper

drainage must be provided to prevent water

from entering the Snorkel Termination. Refer

to Diagram 4. Do not attempt to enclose the

Snorkel within the wall, or any other type of

enclosure.

*Dia 3, 3a & 4: As specified in CGA B149

Installation Code. Local codes or regulations

may require different clearances.

Diagram 1

Horizontal runs of vent must be

supported every three feet. Wall straps

are available for this purpose.

Mark the wall for a 10" x 10" square hole.

The center of the square hole should line

up with the centerline of the horizontal pipe.

Cut and frame the 10 inch square hole in

the exterior wall where the vent will be

terminated. If the wall being penetrated is

constructed of non-combustible material,

i.e. masonry block or concrete, a 7"(178mm)

dia. (7-1/2"(191mm) dia. for flex) hole is

acceptable.

Diagram 2

Note:

The horizontal run of vent must be level,

or have a 1/4 inch rise for every 1 foot

of run towards the termination. Never

allow the vent to run downward. This

could cause high temperatures and may

present the possibility of a fire.

The location of the horizontal vent termi-

nation on an exterior wall must meet all

local and national building codes, and

must not be blocked or obstructed. For

External Vent Terminal Locations, see

diagram in the "Exterior Vent Termination

Locations" section.

Snorkel Terminations:

For installations requiring a vertical

rise on the exterior of the building, 14-

inch and 36-inch tall

Snorkel Terminations

are available, as

well as the standard

Riser Vent. Follow the

same installation

procedures

as used for

standard

Horizontal

Termination.

N E V E R

install the

s n o r k e l

u p s i d e

down.

Diagram 3

Diagram 3a

Note: Riser Vent

is only for use

in above grade

terminations.

NOTE:

For best results and optimum perfor-

mance with each approved venting system,

it is highly recommended to apply “Mill-

Pac” sealant (supplied) to every inner pipe

connection. Failure to do so may result in

drafting or performance issues not covered

under warranty.

Note: With

DuraVent,

the

minimum

height is

achieved by

installing a

elbow

directly to

the top of

the unit.

HORIZONTAL

TERMINATIONS

Install the vent system according to the

manufacturer's instructions included with

the components.

Set the unit in its desired location. Check

to determine if wall studs or roof rafters

are in the way when the venting system is

attached. If this is the case, you may want

to adjust the location of the unit. Rough in

the gas preferably on the right side of the

unit and the electrical (junction block is on

the left side) on the left.

Direct Vent pipe and fittings are designed with

special twist-lock connections to connect the

venting system to the appliance flue outlet. A

twist-lock appliance adaptor is an available

option that must be used in conjunction with

the Simpson Dura-Vent Direct Vent system.

Put a bead of silicone inside the outer section

of the adapter and a bead of Mill Pac on

the inner collar. Slip the adapter over the

existing inner and outer flue collar and fasten

to the outer collar only with the 3 supplied

screws (drilling pilot holes will make this

easier). Level the fireplace and fasten it to

the framing using nails or screws through

the nailing strips.

Assemble the desired combination of pipe

and elbows to the appliance adaptor and

twist-lock for a solid connection.

Note:

a) Twist-lock procedure: Four indentations,

located on the female ends of pipes and

fittings, are designed to slide straight

onto the male ends of adjacent pipes

and fittings, by orienting the four pipe

indentations so they match and slide

in to the four entry slots on the male

ends, Diagram 1. Push the pipe sections

completely together, then twist-lock

one section clockwise approximately

one-quarter turn, until the two sections

are fully locked. The female locking lugs

will not be visible from the outside, on

the Black Pipe or fittings. They may be

located by examining the inside of the

female ends.

Содержание P90-LP10





















































Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products P90-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды