Regency Fireplace Products P90-LP10 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 52

background image

38

|

Regency Excalibur

®

P90-10 Zero Clearance Direct Vent Gas Fireplace

|

38

installation

01/04/08

918-067c

P36D / P90

Page 4 of 4

Place embers in these 3 locations

on the burner tray.

02-50

02-55

02-75

02-53

02-51

02-54

02-52

10)

Place the embers on the front of the burner tray in the

places shown on the photos below.

Separate platinum embers and place on the front burner on

and around the embers. Avoid stacking platinum embers.

Platinum embers may be placed over burner ports.

11)

Test fi re to ensure proper light off (make sure fl ame fl ows

smoothly from one end of burner to the other). If there is

any fl ame hesitation, check that area for any blockage of

the burner ports.

Do not block the burner ports in this

area adjacent to the Log 02-54

02-51

02-54

IMPORTANT

When placing Embers, do not block burner ports as

this can cause an incorrect fl ame pattern, carbon

deposits and delayed ignition.

«
...
36
37
38
39
40
...
»

Содержание P90-LP10





















































Отзывы:

Нет отзывов

Похожие инструкции для P90-LP10

Бренд: Warm House Страницы: 18

Бренд: Majestic fireplaces Страницы: 56

Бренд: HAMPTONBAY Страницы: 30

Бренд: Archgard Страницы: 26

Barcelona FP-BAR00-100

Бренд: Nordpeis Страницы: 16

Бренд: Majestic Страницы: 48

Бренд: Monessen Hearth Страницы: 32

FA902400TX-Espresso

Бренд: SE Страницы: 12

Бренд: Boulevard Страницы: 48

Бренд: Superior Fireplaces Страницы: 32

Бренд: Lennox Hearth Products Страницы: 16

Бренд: Coleman Страницы: 8

e-MatriX 800/650

Бренд: Faber Страницы: 8

e-MatriX 800x500-RD

Бренд: Faber Страницы: 10

Бренд: Faber Страницы: 37

BarcelonaLights36ZEN

Бренд: IHP Страницы: 40

PYROTECH DELUXE

Бренд: RealFlame Страницы: 32

Ledgestone T0027

Бренд: RealFlame Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды