Regency Fireplace Products P90-LP10 Скачать руководство пользователя страница 41

Страница: 41 / 52

Regency Excalibur

P90-10 Zero Clearance Direct Vent Gas Fireplace

operating instructions

AERATION

ADJUSTMENT

The air shutter can be adjusted by moving the

adjusting wire up or down. The wire is accessed

through the bottom louver opening. Open the air

shutter for a blue flame or close for a more yellow

flame. The burner aeration is factory set but may

need adjusting due to either the local gas supply

or altitude.

Minimum Air Shutter Opening:

3/16"

Natural Gas

5/16"

Propane

CAUTION:

Carbon will be produced if air shutter

is closed too much.

Note: Any damage due to carboning resulting

from improperly setting the aeration

controls is NOT covered under warranty.

Note: Aeration Adjustment should only be

performed by an authorized Excalibur

Installer at the time of installation or

service.

Adjustment Wire: Push to close or

pull to open aeration cap.

Closed - Tall yellow

Open - Short Blue

Содержание P90-LP10





















































Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products P90-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды