Regency Fireplace Products P90-LP10 Скачать руководство пользователя

Страница: 35 / 52

Regency Excalibur

P90-10 Zero Clearance Direct Vent Gas Fireplace

installation

LOG SET INSTALLATION

01/04/08

918-067c

P36D / P90

Page 1 of 4

Notch

Bracket

02-51

02-75

02-51

Place the Log 02-75 on the rear log support pins with the

fl at side to the back.

LOG SET INSTALLATION

Carefully remove the logs from the box and unwrap them.

The logs are fragile, handle with care -

do not force into

position.

The "02" reference numbers (i.e. 02-75) are

molded into the rear of each log.

02-75

Notch

Read the instructions below carefully and refer to the

diagrams. If logs are broken do not use the unit until

they are replaced. Broken logs can interfere with the

pilot operation.

The gas log kit (Part #780-930) contains the following

pieces:

a) 02-75

Rear Log

b) 02-55

Middle Left Log

c) 02-50

Front Left Log

d) 02-53

Center Left Log

e) 02-51

Front Bottom Log

f) 02-54

Center Right Log

g) 02-52

Middle Right Log

h) 902-156 Embers

i) 902-179 Vermiculite

j) 946-669 Platinum Embers

(supplied with packaged manual)

NOTE: If you will be installing the optional Brick Panels

(P36D & P90 only), install the Brick Panels prior

to installing the logs.

Model shown has P36D and P90 burner/grate with

brick panel option.

Place Log 02-51 on the front right side of the burner. Push

the back of the log against the 2 brackets with the notch

on the bottom right side of the log fi tting into the right side

of the grate.

Sprinkle the vermiculite over base brick panel.

02-75

02-51

02-53

02-54

02-55

02-52

02-50

Содержание P90-LP10





















































Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products P90-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды