Regency Fireplace Products P90-LP10 Скачать руководство пользователя страница 13

Страница: 13 / 52

Regency Excalibur

P90-10 Zero Clearance Direct Vent Gas Fireplace

installation

Fireplace

Stand

No hearth is
required when

the unit is raised

3" (76mm) off of
the floor surface

Floorin

HEARTH REQUIREMENTS

Floor Mounted Fireplaces

Raised Fireplaces

FACING REQUIREMENT

This fireplace requires a non-combustible material extending from the

framing header and sides.

The flanges on the front face of the fireplace are for a facing thickness

of 3-3/8" (86mm).

Facing Over 3-3/8" (86mm) Thick

If the facing material is over 3-3/8" (86mm) thick (example: brick or river

rock), install the facing around the perimeter of the face. You may wish

to make a face template as shown on the diagram.

Regency provides a

template on the box.

NOTE:

If using a brick

hearth, the fireplace will

need to be raised to

accommodate the brick

thickness. Example: If the

brick is 2" thick, the unit

must be raised 1".

Note: 48" (11219mm) is the

minimum height for

both flex termination

or Rigid Pipe venting.

4. Note: The unit does not

have to be completely

enclosed in a chase. The

clearance on top of the

unit is 0" to the standoffs

so combustible building

materials can be laid

directly on top of the

standoffs. You must

maintain clearance from

the vent to combustible

materials for both

rigid and flex, see the

"Clearances" section.

You must take into account

the depth of the floor covering

(carpet, tile, linoleum, etc.) when

determining the height of the

fireplace stand.

The

HeatWave

Duct Kit has different

clearance and framing requirements, check

the

HeatWave

manual for details.

Please note that all vertical measurements are taken from the

base of the unit

excluding

risers or bottom stand-offs.

Содержание P90-LP10





















































Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products P90-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды