Regency Fireplace Products P90-LP10 Скачать руководство пользователя

Страница: 45 / 52

Regency Excalibur

P90-10 Zero Clearance Direct Vent Gas Fireplace

maintenance

Connect fan ground cable to ground lug. Refer

to wiring diagram.

Slide the thermodisc/cover assembly into the

bracket clip on the underside of the firebox.

Check that no wire will touch the hot surfaces.

Diagram 2.

Install the Fan Control Module (FCM) on the base

of the unit to the left of the gas valve. Plug the

FCM into the outlet.

Plug in the fan power cord to the Fan Control

Module into the outlet marked “Fan”. Plug the

FCM-COM wire from the remote control wiring

harness into the location on the Fan Control

Module marked “COM”. Turn the switch on the

Fan Control Module to the ON position. ON is to

the left. The “O” is the off position.

Diagram 1

Diagram 3

Diagram 2

Secure the fan wires and power cord by attaching

one of the adhesive backed wire holder clips.

onto the stove base. Use the second clip to

bundle up the wires approximately 4" from the

control box. Ensure that there is no interference

with the wires when the louver is closed and

that no wire will touch the hot metal surfaces

or sharp edges.

Plug the fan power cord into the rear end of

the receptacle box to provide the maximum

clearance from the louvers.

To Remove the Fan

Shut the power off.

Reverse the above instructions.

Note: The bearings are lubricated for life. Do

not lubricate them. Make sure you vacuum

the fan area on a regular basis.

IMPORTANT:

These fans collect a lot of dust from within

your home. Ensure you maintain these fan

motors on a regular basis by vacuuming

out the fan blades and housing using a soft

brush nozzle.

FAN MAINTENANCE

120 Volt AC power is needed for the fan. The fan

can be hard wired if desired. The outlet should be

installed in the receptacle box on the left hand side

by a qualified electrician. The neutral (wider) slot of

the polarized outlet should be at the top.

Unit must be grounded at all times. Do

not cut the ground terminal off under any

circumstances.To Install the Fan

Shut the power off.

Remove the bottom louver door.

Slide the fan in towards the rear of the unit and

slip it over the two mounting studs. Take care

not to damage the insulation on the fan base.

Ensure that the fan blades do not rub against

the valve tubing.

Diagram 1.

IMPORTANT:

THESE FANS COLLECT A LOT OF

DUST FROM WITHIN YOUR HOME.

ENSURE YOU MAINTAIN THESE FAN

MOTORS ON A REGULAR BASIS BY

VACUUMING THE FAN BLADES AND

THE HOUSING WITH A SOFT BRUSH

NOZZLE.

Содержание P90-LP10





















































Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды

Regency Fireplace Products P90-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание P90-LP10

Отзывы:

Похожие инструкции для P90-LP10

Бренды по названию

Популярные бренды