background image

12

www.redbacklasers.com.au

Rotation Scan Modes - For Indoor Visibility

The DGL1010VS is also useful for indoor visual levelling and alignment, with 

Scan Mode you can produce horizontal level lines on walls or when operated 

on its side, vertical lines.

The Scan Mode stops the laser from rotating and toggles the beam left to 

right, intensifying the beam making the laser more usable indoors as a visible 

laser.  To activate scan mode press the Scan Mode button          .You can set 

the scan angle to 180

o

, 45

o

, 10

o

 and DOT each press of the scan mode button 

toggles through the different angles.  To shift the beam use the left and right 

Scan Adjustment buttons            .  Scan Mode can be operated by both the 

Control key pad on the laser and also the Remote Control.  To return the 

DGL1010VS back to rotating mode press the Rotation button          .

DGL1010VS OPERATING INSTRUCTIONS

Remote Control Operation 

(refer to diagram page 5)

The DGL1010VS has a sophisticated radio frequency remote control with full 

LCD display that provides real time information to and from the laser.  Radio 

frequency means that you have you an exceptional range of up to 50m it 

also means easier communication even from within the cab of a machine.

The LCD Display means that all the features of the laser are at you finger 

tips, you can even instantly see from the display if the laser has “tilted” and 

press the level button to getting it going again without leaving the cab.

The receiver has multiple channels the default being channel #1 the channel 

number is displayed on both the LCD on the DGL1010VS and the remote 

bottom left corner.  If you have a second DGL1010VS on site the channel 

can be changed on the second laser and remote so as not to interfere, this is 

done by pressing the Remote button           and toggling to the next channel. 

Note this needs to be set separately on both the laser and remote unit so 

both show the same channel number, if the laser does not detect a turned 

on remote on the selected channel the antenna symbol on the bottom left 

corner of the laser LCD has a line through it. 

Содержание DGL1010VS

















Отзывы: