background image

3

DGL1010VS INTRODUCTION

Congratulations on purchasing the DGL1010VS an electronic self levelling 

dual grade rotating laser level built tough to handle the harshest of job sites.

The DGL1010VS is ideal for building, plumbing and earthmoving, simply 

set it up on a tripod, turn on, it electronically self levels and the laser starts 

rotating.  Then using the supplied receiver you can set up your levels or 

grades. 

The DGL1010VS has fully automatic dual grade setting capability simply 

punch in the desired grade to three decimal places either on the keypad or 

remote and the laser does the rest.  The sophisticated grade and levelling 

technology continually re levels and re-sets the grade if required. 

The DGL1010VS also features a smart long range remote control complete 

with an LCD display duplicating the display on the laser level itself.  This 

make setting grades and the DGL1010VS other features a snap.

The DGL1010VS can also be used on its side for vertical alignment and site 

square layout and has scan modes essential for indoor visible use.

The DGL1010VS comes with superior rechargeable Li-ion batteries but 

can also use Std “D” Size batteries if needed and comes with a Five Year 

RedBack Warranty. (See page 16)

www.redbacklasers.com.au

DGL1010VS Included Accessories

• 

DGL1010VS Laser Unit

• 

Hard Shell Carry Case

• 

Rechargeable Li-ion Batteries

• 

Charger

• 

Laser Receiver 

(LR715 or LR720)

• 

Receiver Staff Clamp

• 

Grade Alignment Scope

• 

Smart Remote Control

• 

 

Side Plate for Squaring

• 

 

Axis Adjustment Plate

• 

Instruction Manual

Содержание DGL1010VS

















Отзывы: