RAYLASE AXIALSCAN Скачать руководство пользователя страница 51

Страница: 51 / 71

Troubleshooting

Chapter 7

MN025 / v2.1.0

3-Axis Subsystems for Laser Beam Deflection

TROUBLESHOOTING

Warning:

The laser beam can cause severe injury to the eyes and the skin.



Never look directly or indirectly into the laser beam during troubleshooting.



Do not disable any safety precautions to protect against laser radiation.



Wear protective clothing and/or goggles appropriate for the relevant laser

class.

In case of malfunctions, check whether the symptom and a possible remedy are included in
the following checklist.

Problem

Possible cause and remedy

Poor marking
quality

Defective power supply

Incorrect marking parameters

Marking quality
has deteriorated

Dirty optical
system



page 49, Instructions for cleaning lenses and protective

glasses



page 49, Instructions for cleaning mirrors

Laser power
decreasing

The RAYLASE weldMARK

™

marking software can compensate

for a loss of laser power.
Menu: System > Global adjustments

Marking parameters changed

Beam expander changed

Laser spot
changed

Dirty optical
system



page 49, Instructions for cleaning lenses and protective

glasses

Dirty or dam-
aged mirrors



page 49, Instructions for cleaning mirrors

Send deflection unit in for repair

Laser system out of adjustment

No laser beam,
although pro-
cess started
from PC.

Beam path
blocked.

Remove protective cover from beam input and/or output

Fault in laser drive

Fault in laser system

The deflection
unit only de-
flects the laser
beam in one
direction or not
at all.

Data cable de-
fective



page 13, Status LED of the linear translator module

X and Y axis
reversed

Incorrect cabling

If the fault cannot be resolved, contact RAYLASE Customer Service for further assistance.

Содержание AXIALSCAN








































































Результаты поиска

Содержание AXIALSCAN

Отзывы:

Похожие инструкции для AXIALSCAN

Бренды по названию

Популярные бренды

RAYLASE AXIALSCAN, Руководство пользователя

Результаты поиска

Содержание AXIALSCAN

Отзывы:

Похожие инструкции для AXIALSCAN

Бренды по названию

Популярные бренды