RadioLink AT10II Скачать руководство пользователя страница 49

Страница: 49 / 88

Radiolink Electronic Ltd

www.radiolink.com

*If you receive an error message that OTHER WING MIXING IS ON, you must deactivate ELEVON

or FLAPERON.

3.3.6 Air Break (ACRO/ GLID)

ACRO

GLID

Like FLAPERON and AILEVATOR, AIRBRAKE is one function that is really made up of a series of

pre-programmed mixes all done for you within the radio. AIRBRAKE (often called "crow" or

BUTTERFLY - see GLID, p. 62 for details) simultaneously moves the flap (if installed), twin ailerons

(if installed) and elevator, and is usually used to make steep descents or to limit increases in

airspeed in dives.

This function is often used even on models without flaps as an easy way to use the FLAPERON and

FLAP-ELEVATOR mixing together.

ADJUSTABILITY:

• Activation: be proportional by moving the THROTTLE STICK, or set positions by flipping the

assigned switch.

• Switch: Mix SWITCH is selectable.

• Also LOGIC SW (Lsw1 to 3) may be assigned.

• Linear(Inversely proportional to THROTTLE STICK): Provides a proportional increase in amount

of AIRBRAKE action as THROTTLE STICK is lowered and assigned switch is on. It provides

gradually more AIRBRAKE as you slow the engine. Includes selectable stick position where

AIRBRAKE begins, gradually increasing to the same setting as the THROTTLE STICK is lowered. If

you would like to have the airbrake be directly proportional to throttle stick, you will

need to reverse the THR-REV function. Note that this changes the throttle stick direction for all

models.

• Offset: Provide AIRBRAKE response immediately upon switch movement, going to a pre-set

travel on each active channel without any means of in-flight adjustment.

• During Airbrake operation, the elevator travel is displayed on the elevator trim display in the

Startup screen.

•Delayed reaction: You can suppress sudden changes in your model's attitude when AIRBRAKE

BUTTERFLY is activated by setting the delay (delay-ELEV) item, to slow down the elevator

response, allowing the flaps/ailerons/elevator to all reach their desired end point together. A setting

of 100% slows the servo to take approximately one second to travel the prescribed distance. (GLID:

B.FLY-ELEV function)

• Adjustable in flight (ACRO): Using the aileron (when AILE-DIFF or FLAPERON is activated) and

elevator trim lever in flight can be set to adjust the aileron and elevator settings in your airbrake

rather than adjusting the model's actual aileron and elevator trim. This allows easy adjustment for

any ballooning while in flight. When the airbrake switch is moved to off the trim is again adjusting

the normal elevator trim.

• Channels controlled: Elevator, twin ailerons and flap may be set independently in AIRBRAKE,

including set to 0 to have no effect.

• If FLAPERON is active, the travel of the ailerons can be independently adjusted for the servos

plugged into CH1 and CH6. The flap choice has no effect on the FLAPERON.

• If AIL-DIFF is active, then CH1 and CH7 may be independently adjusted.

• Normally both ailerons are raised equally in AIRBRAKE, and the elevator motion is set to maintain

trim when the ailerons rise. Different amounts may be set for each aileron to correct for torque

Содержание AT10II

























































































Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды

RadioLink AT10II, Инструкция по эксплуатации

Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды