RadioLink AT10II Скачать руководство пользователя страница 16

Страница: 16 / 88

Radiolink Electronic Ltd

www.radiolink.com

Antennas should be kept away from metal conductor and carbon fiber at least half inch

away and no over bending.

Keep antennas away from motor, ESC or other possible interference sources.

Note

Receiver contains some electronic components of high-precision. Be careful to avoid strong

vibration and high temperature.
When all the above steps are complete, please turn off the transmitter and repower on to test if the

receiver is correctly connected with it.

2. Transmitter Antenna Installment

The transmitter antenna is adjustable so please make sure that the antenna never points

directly at the model when flying as this may possibly decrease the receiver signal.

Keep the antenna perpendicular to the transmitter to optimize the receiver performance. It

also depends on how you hold the transmitter. But in most cases, adjusting the antenna with

perpendicular position to the transmitter surface will achieve the best result. Please adjust the

transmitter antenna according to the way you hold the transmitter.

Never grip the antenna when flying as this degrades effective control range.

1.3 RADIO BASIC SETTING

1.3.1 Basic setting of the transmitter

(1) Display language: can be selected the display language of the function name, etc. in each

function menu. The screen reads "LANGUAGE". Change this to the desired language.

(2) Stick Mode: The screen reads "STK-MODE". Change this to the correct mode. Note that this will

NOT change the throttle and elevator ratchets, etc. Those are mechanical changes that must be

done by a service center.

(3) RF Mode: the LED indicator will become solid green when RF Mode is active.

(4) Adjusting Display Contrast: To adjust the display contrast, from the home menu press and hold

the END BUTTON. Turn the DIAL while still holding the END BUTTON: clockwise to brighten and

counterclockwise to darken the display.

(5) User name setting: user name can be set by DIAL and PUSH with letters and numbers.

(6) Alarming voltage:

Transmitter: preset 8.6V, can be self-set

Receiver: preset 4.0V, can be self-set

Ext: preset 10.1V, can be self-set

1.3.2 Model type

Under basic menu, use CURSOR to select MODEL TYPE and enter by pressing PUSH. There are

6 different type included in the system, HELICOPTER, AEROBASIC, GLID(1A+1F), GLID(2A+1F),

GLID(2A+2F), and MULTIROTOR, after model type is selected, press and hold PUSH for 1 second,

when the word “are you sure to change” displayed, model type is changed.

Содержание AT10II

























































































Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды

RadioLink AT10II, Инструкция по эксплуатации

Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды