RadioLink AT10II Скачать руководство пользователя страница 73

Страница: 73 / 88

Radiolink Electronic Ltd

www.radiolink.com

Change to desired

SWASH TYPE (Ex:

HR3) Confirm.

to SWASH.

HR3,

for 1 sec. ‘Are you

sure?’ displays.

Radio emits a repeating “beep” and shows progress on screen as the model type is being changed.

Note that if the power switch is turned off prior to completion, the model type will not be changed.

5.2.2 SWASH AFR (not in SWH1)

Except SWASH PLATE, function menu of helicopter is same as GLID/ ACRO. Please find the

former instructions.

Swash plate function rate settings (SWASH AFR) reduce/increase/reverse the rate (travel) of the

aileron, elevator (except H-2) and collective pitch functions, adjusting or reversing the motion of all

servos involved in that function, only when using that function. Since these types utilize multiple

servos together to create the controls, simply adjusting a servo's REVERSE or END POINT would

not properly correct the travel of any one control. Since H-1 uses one servo for each function, there

is no need for AFR in H-1.

Since aileron always uses no more than 2 servos, check it first. Either both operate properly (no

change needed), both operate backwards (reverse the whole function), or one servo operates

backwards (reverse that servo alone). Next check elevator. Remember, the aileron servo(s) operate

correctly, so if elevator does not, we should only have 2 choices left—the whole function needs to

be reversed, or the servo(s) not shared with aileron need to be reversed. If aileron and elevator are

not working properly, the only thing that could be wrong is the whole direction collective operates

(reverse the whole function). In our example, HR3 is 180 degrees off from the swash plate of the

Caliber. Therefore, it is very likely that several functions will not operate properly. The collective

pitch operation is backwards; but reversing all three servos would also reverse the aileron and

elevator operations. Changing the collective pitch rate, however, from +50% to -50%, will reverse

the collective pitch without affecting the aileron action.

Checking For Proper Motion On An HR3 Swashplate

HR3 Swash Typ Proper Motion

Wrong Motion

How to Fix

AILERON

STICK.

Swashplate tilts left.

Reverse AIL setting in SWASH

to -50%.

Swashplate tilts right. Back of Swashplate

moves up.

Ch6 servo moves incorrectly;

REVERSE.

Back of Swashplate

moves down.

Ch1 servo moves incorrectly;

REVERSE.

Содержание AT10II

























































































Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды

RadioLink AT10II, Инструкция по эксплуатации

Результаты поиска

Содержание AT10II

Отзывы:

Похожие инструкции для AT10II

Бренды по названию

Популярные бренды