background image

BLUES30/50NV

ELETTRONICA

15

 

/ 28

User Manual

Rev. 1.0 - 29/11/16

1b) To 

modify power level setting

, hold down the 

ENTER

 button until opening 

the 

power setup menu

.

  The edit screen will look like this:

Menu 2

The bottom line gives the instantaneous reading of the power (50W in this example), 

to increase the level rotate towards right, to reduce it rotate towards left. When the 

desired level is reached, press the encoder to confirm and exit to the predefined 

menu. Note that the set value is stored anyway, so if you pass the time-out without 

pressing a key, the power will remain at the last set level. 

 

NOTE:

 

This feature prevents the equipment from delivering maximum power 

as soon as output is enabled from menu 4, or in the event the equipment is 

already set to 

ON

 when you energise it.

2)  Ensure that the equipment is not in a locked-out state. Push the encoder to call 

up the selection screen (menu 3). Highlight Fnc and then confirm by pushing 

the encoder and access the selected menu (menu 4).

  In the same menu, ensure that power limiting is disabled: if 

PWR

  is set to OFF, 

i.e. power output is disabled, move cursor to PWR. Press ENTER and label 

will switch to ON, i.e. power output enabled.

  Press 

ESC

 twice to go back to the default menu (menu 1).

3)  Fine tune power setting from menu 2 (see description of item 1b) until achieving 

the desired value.

 

WARNING: Equipment is capable of delivering more than rated output power 

of 30/50 W; however, never exceed the specified power rating.

 

NOTE:

 

If power is set to 0 W in the 

Power Setup Menu

, the INTERLOCK OUT 

contact is activated and any external appliances connected to it are immediately 

inhibited.

Next,  you  can  review  all  operating  parameters  of  the  equipment  through  the 

management firmware.

Normally,  the  equipment  can  run  unattended. Any  alarm  condition  is  handled 

automatically by the safety system or is signalled by the LED indicators on the 

panel or by display messages.

 

NOTE:

  Standard  factory  settings  are  output  power  set  to  upper  limit  (unless 

otherwise specified by customer) and 

OFF

.

Содержание BLUES30NV




































Отзывы: