background image

BLUES30/50NV

ELETTRONICA

11

 

/ 28

User Manual

Rev. 1.0 - 29/11/16

      

Note: 

the  mains  must  be  equipped  with  adequate  earth  connection  properly 

connected to the equipment. This is a pre-requisite for ensuring operator safety 

and correct operation.

Connect the audio and RDS/SCA signals from user’s sources to the transmitter 

input connectors.

  5.1.3  Encoder

The interaction between the user and the exciter control software is performed 

using the encoder.

Ruotare l’encoder verso sinistra 

per spostare il cursore verso il 

basso, per decrementare il valo-

re di un parametro o per selezio-

nare un elemento di una lista

Ruotare l’encoder verso destra 

per spostare il cursore verso l’al-

to, per incrementare il valore di 

un parametro o per selezionare 

un elemento di una lista

Premere il pulsante una volta per 

entrare nel menù desiderato, quindi 

una seconda volta per modificare il 

parametro selezionato.

The operations that you can perform on the encoder are:
• 

rotation

: moves the cursor shown on the display; if you turn the encoder to 

the left (counterclockwise), the cursor moves downwards, if you turn it right the 

cursor moves upwards; it also permits to increase or diminish the parameters 

(turning the encoder left diminishes the paramete.

• 

pression

: push the button once when the cursor is on the name of a menu to 

enter in that menu, push it when the corsor is on the name of a parameter to 

enter in modification mode (the cursor starts blinking); after the modification of 

a parameter, push the button to save the new value.

After having modified the value of a parameter, the cursor goes on blinking for 

approximately  15  seconds,  waiting  for  confirmation  from  the  user.  If  the  user 

doesn’t confirm the new value (i.e., the button is not pressed), the parameter has 

not saved and remains on the selected parameter.

The first pressure of the encoder when the display is light out, or its rotation, serves 

in order to activate the retroillumination.

Содержание BLUES30NV




































Отзывы: