background image

BLUES30/50NV

ELETTRONICA

13

 

/ 28

User Manual

Rev. 1.0 - 29/11/16

The screen in edit mode will look like this:

 

The bottom line gives the instantaneous power (50W in this example), to increase 

the level, turn to the right to turn to the left. Once you reach the desired level, press 

the ENCODER to confirm and exit to the default menu. Note that the set value is 

stored anyway, so if you leave the timeout without pressing any key, the power 

will be the last level set.

The value at the side of 

SET

 provides a percentage indication of power setting; 

please consider that the forward power readout provided on the display (

FWD: 

xxxx W

) reflects actual output power reading, 

which may be lower than regulated 

power  supply  when Automatic  Gain  Control  is  running  in  power  supply 

limitation mode

 (please read section 5.3 about RF power supply modulation for 

more details).

      

NOTE: 

Output power may be set using the 

Pwr OFF

 control. In this condition, the 

output power readout (

Fwd

) on the display will read 0 (zero); the 

SET

 bar will reflect 

any adjustments you make using the keys and provides a graphic indication of how 

much power supply will be delivered the moment you return to 

Pwr On

 state.

  5.2.5  Changing the 

Power Good

 alarm threshold

Change Forward Power Good alarm setting 

PgD

 from the 

Fnc

 menu as desired 

(factory setting is 50%).

  5.2.6  Setting equipment I

2

C address

Change  the 

IIC

  address  in  the 

MIX

  (Miscellaneous)  menu  as  desired  (factory 

setting is 01).

  5.2.7  Adjustments and calibration

The  only  manual  adjustments  are  the  level  adjustments  and  the  audio  mode 

adjustment.

The rear panel holds the trimmers for all transmitter inputs. Trimmer identification 

is printed on the rear panel. Input sensitivity can be set within the limits set out in 

the tables below through the trimmers:

Содержание BLUES30NV




































Отзывы: