Proxim Tsunami MP-8100 Series Скачать руководство пользователя страница 79

Страница: 79 / 99

Event Log Error Messages

Tsunami MP-8100 Reference Manual

ERROR

tftp: Read on the new
firmware failed

Firmware file not readable;
hence invalid.

Check the image file and
the license. Contact
customer support if the
problem persists.

ERROR

Image size not equal to bytes
read

Download operation is not
successful.

Check network
configuration and retry.

ERROR

Image flashing failed

Not able to save the image.

Retry after reboot.

INFO

tftp: System is going to reboot

Image file successfully written to
flash after download and system
is going to reboot and come up
with the new image.

NONE

ERROR

Image ID Does not Match

Image ID does not match with
the firmware ID in the device.

Check image file and
license before retrying.

ERROR

Unable to create ‘image name’
file

Unable to create a file with the
given image file name.

Reboot the device and
retry.

INFO

‘image name’ File Write Error

Unable to write the image file

obtained into flash

Reboot the device and
retry.

ERROR

Unable to Close the ‘image file’
File

Unable to write the image file
obtained into flash.

Reboot the device and
retry.

ERROR

Error in Flash write

Unable to write the image file
obtained into flash.

Reboot the device and
retry.

ERROR

TFTP operation in progress...

Another operation is selected
while TFTP operation was in
progress.

Check your configuration
and retry.

ERROR

We couldn't fork a child
process, may be because of
lack of memory

TFTP operation failure.

Reboot the device and
retry.

ERROR

Couldn’t create the status file

TFTP operation failure.

Reboot the device and
retry.

ERROR

Invalid Config ID returned by
Flash module

The current configuration file
may belong to an older build.

While updating the
image, it is advised to
remove the current
configuration.

ERROR

File Name given is not valid [
~`!$^&*()=|\\{}[];\"'<>? ]
should be avoided in filenames

Avoid any special characters
while providing file name.

Check the file name.

Error Type

Message

Description

Corrective Action

Содержание Tsunami MP-8100 Series




































































































Результаты поиска

Содержание Tsunami MP-8100 Series

Отзывы:

Proxim Tsunami MP-8100 Series, Справочное руководство, Страница: 79 / 99

Результаты поиска

Содержание Tsunami MP-8100 Series

Отзывы: